Yamaha pdm-4210 User Manual
35
ENGLISH
OPERATING INSTRUCTIONS (continued)
Displaying MULTI PICTURE
If the PinP button on the remote control is pressed
MULTI PICTURE will display.
MULTI PICTURE will display.
Activating the P-in-P mode from the RGB input screen
Pressing the PinP button once will display 2 pictures.
• This mode can be available from RGB1(DVI-PC) and RGB2(RGB)
input.
• The speaker icon can be shifted left and right by pressing the
and
SELECT buttons; the audio of the video will be output from
the side on which the speaker icon is located.
• The sub-screen position can be
selected up and down by pressing
SELECT buttons.
• When the speaker icon appears on
the left of the subscreen, as in the
illustration at right, you can use the
AV1, AV2, AV3, or AV4 buttons to
select the subscreen input mode.
illustration at right, you can use the
AV1, AV2, AV3, or AV4 buttons to
select the subscreen input mode.
• Pressing the PinP button or the
RETURN button will cancel the 2 pictures display.
• "Frequency Mode" in the Setup Menu should be set to Movie when
sub-screen is the component signal of 1080i/50 or 1080i/60.
AV1: Displays the VIDEO input signal of the sub-screen.
Activating the Split mode from the video input screen
Pressing the PinP button one time will display 2 pictures.
• The speaker icon can be shifted left
and right by pressing the
and
SELECT buttons; the audio of the
video will be output from the side on
which the speaker icon is located.
video will be output from the side on
which the speaker icon is located.
• The same video input mode cannot
be selected for both screens at the
same time.
same time.
• Pressing the PinP button or the
RETURN button will cancel the 2 pictures display.
• When the Video input is set to RGB Video, this Split mode is not
possible.
• Refer to the table for 2 pictures (Split) mode.
PinP button
RETURN button
AV1
AV2
RGB 1
RGB 2
AV3
MUTE
VOL
VOL
AV4
AUTO
PinP
OK
SIZE
RECALL
MENU
ID
ID SET
RECALL button
RGB2
AV1
(Sub-
screen)
screen)
AV1
AV2
RECALL button
2 Pictures (Split)
Main
Sub
The input signal status can be displayed on the screen
by pressing the RECALL button of the remote control or
the monitor.
by pressing the RECALL button of the remote control or
the monitor.
• The display will go out in approximately 6 seconds.
AV1
Composite
-- -- Min.
-- -- : -- --
OFF
Input Signal Screen Display
Input mode
Signal mode
Signal mode
Off-timer
On-timer
On-timer
VIDEO
NOTE
• Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not
change to power save mode.
• Please be careful since image retention will occur if the plasma monitor is left in MULTI PICTURE display state for a long period of time.
Input terminal
AV1
∼AV4
AV1, AV2
RGB1
RGB2
PAL-N
NTSC-M
PAL-M
576i
576p
480i
480p
1080i/50 1080i/60 720p/60
STB
Component
AV1
∼AV4
PAL-N
○
○
○
○
○
○
○
NTSC-M , PAL-M
○
○
○
○
○
○
○
AV1
AV2
AV2
576i, 576p
○
○
480i, 480p
○
○
1080i/50
○
○
1080i/60
○
○
720p/60
○
○
RGB1
STB
RGB2
Component
○
○
○
○
○
○
○
(
○ : Available)
Main
Sub
015_PDM-4210_U_E 2003.12.24 18:37 ページ 35 (ブラック 版)