Zoom 8080 Operating Guide
25
■
Advanced
Operation
Press the
once to
display the RTM
parameter.
parameter.
Except for the TOTAL and EQ
modules, page 2 of every effect
module includes the RTM
parameter.
"RTM" (RTM destination) stands for
the parameter to be controlled by RTM.
"DIR" (RTM direction) stands for the
direction in which the parameter is to be
controlled.
"DIR" (RTM direction) stands for the
direction in which the parameter is to be
controlled.
UTILITY/PAGE key
5
Use 4
to
select the direction
for the "RTD=" item.
for the "RTD=" item.
You can select either "NML"
(normal) or "INV" (inverted).
(normal) or "INV" (inverted).
The meaning of "NML" and "INV"
depends on the effect type
controlled by the pedal.
depends on the effect type
controlled by the pedal.
Data entry knob
7
Use 3
to
select the parameter
(only for effect types
where the RTM
destination can be
(only for effect types
where the RTM
destination can be
selected).
Data entry knob
6
If desired, store the
patch.
patch.
("Storing an edited patch"
p. 23).
8
Operate
while playing the
instrument.
while playing the
instrument.
The selected effect module
parameter changes according to
the pedal movement. In this
example, the compression depth
can be adjusted with the pedal.
CONTROL pedal 2 can be assigned
in the same way.
parameter changes according to
the pedal movement. In this
example, the compression depth
can be adjusted with the pedal.
CONTROL pedal 2 can be assigned
in the same way.
CONTROL pedal 1
CONTROL
PEDAL
9
FLG
é RTM=SPD DIR=NML
FLG
é RTM=FB DIR=NML
For effect types where the RTM destination can be
changed (some effect types in effect modules EFF2 and
EFF3), the indication "RTM=" is shown on the display,
and data entry knob 3 can be used to select the
parameter. For effect types where the RTM destination is
fixed, "RTM →" is shown on the display.
changed (some effect types in effect modules EFF2 and
EFF3), the indication "RTM=" is shown on the display,
and data entry knob 3 can be used to select the
parameter. For effect types where the RTM destination is
fixed, "RTM →" is shown on the display.
The "Minimum" value of the DIST module depends on the
distortion type and the parameter setting value.
distortion type and the parameter setting value.
In Play mode, the
lower line of the
display shows the
modules assigned to
CONTROL pedals 1
and 2.
lower line of the
display shows the
modules assigned to
CONTROL pedals 1
and 2.
In principle, CONTROL pedal 1, CONTROL pedal 2, and
the CONTROL switches cannot be used to control the
the CONTROL switches cannot be used to control the
same effect module. If an attempt is made to assign
several controllers to the same module in step 3 (TOTAL
module setting), priority will automatically be set in the
order CP1, CP2, CSW.
several controllers to the same module in step 3 (TOTAL
module setting), priority will automatically be set in the
order CP1, CP2, CSW.
TOTAL module setting
Play mode display
The minimum value of the distortion gain control varies
according to the type of distortion and the parameter settings.
The minimum value achieved by these changes may be smaller
than Gain 1, depending on the settings.
according to the type of distortion and the parameter settings.
The minimum value achieved by these changes may be smaller
than Gain 1, depending on the settings.
HINT
HINT
HINT
HINT
HINT
HINT
01 8080LEAD LVL=100
AMP ¡EF2 ™OFF ßHLD
CP1 setting CP2 setting
Controlling VIB (Vintage Vibe) and PPIT (Pedal Pitch Shifter) with the pedals
Pedal released
Pedal depressed
NML
Minimum
Maximum
INV
Maximum
Minimum
Controlling effect types of DIST effect module with the pedals
Pedal released
Pedal depressed
NML
( Minimum value for setting)
Preset parameter value
INV
Preset parameter value
( Minimum value for setting)
Controlling other effect types with the pedal
Pedal released
Pedal depressed
NML
Minimum
Preset parameter value
INV
Preset parameter value
Maximum
NO
✎
NO
✎
CONTROL SET: CSW=DLY
é 2 CP1=DST CP2=DST
If the same module was
assigned to CP1 and CP2 ...
assigned to CP1 and CP2 ...
01 8080LEAD LVL=100
AMP ¡DST ™OFF ßHLD
CP1 is selected and CP2
becomes "OFF".
becomes "OFF".