Skylink WR-001 User Manual

incandescent light or dimmable 

compact fluorescent light with a maximum load 

Light 

bulbs must be dimmable in order to achieve dimming function.

respectively to the existing wires from the wall : Load(Red) to load and 

    Live(Black) to live.

 Secure the Wall Dimmer with the provided screws.

 The two blue LEDs will be on.

tap the metal touch pad to turn ON/OFF the connected light or 

    to 

Setup of the Wall Dimmer is simple. Simply replace your existing wall 
switch by the Wall Dimmer. 

1. Turn off power to the circuit that you plan on installing the Wall Dimmer 
    to at the circuit breaker. 

Note: Lighting Load

The Wall Dimmer is designed to operate 

 

of 600W at 120VAC.  

2. Follow the diagrams below to install the Wall Dimmer with the 2 wires: 
    Live, Load.  Use the provided wire nuts to connect these wires 
    

.

3. After all the wires are connected, ensure that all of the wire connectors 
    are attached securely and there should be no exposed copper wiring. 
   
4. Place the air gap switch to off position.
5. Turn the circuit breaker back on.
6. Place the air gap switch to on position. 
7. The light connected will be off. The Wall Dimmer is now installed and 
    you can 

begin programming to learn transmitters into the Wall Dimmer. 

In order to operate the 

 remotely with a transmitter or sensor,

it must be programmed to the 

.  Each module can be operated 

by up to 8 different transmitters (or 8  different command signals). 

1) Regular Mode - When a valid signal is received,  it will turn on or off the 
    light, or change the brightness of the  light.

2) Flashing Alert Mode - When a valid signal is received, the light  will flash 
    for a specific period of time, which is  the time defined in the timer duration. 
    This works as an alert indication. 

3) Countdown Timer Mode - When a valid signal is received, the light will 
    be on for a specific period of time,  1 minute, 5 minutes, 15 minutes, 
    30 minutes, or 60 minutes. This is mainly for  energy saving.

Wall Dimmer

Wall Dimmer

You can program multiple buttons/transmitters / sensors to the module 
and different button/transmitter / sensor can activate a different mode.

Touch the touch 

    pad. 

1. Wall Dimmer must be installed and powered properly. 

The connected light should be on, and the 2 blue LEDs are off.

2. Press and hold the “SET” button for about 3 seconds,  until the upper 
    blue LED flashes quickly. 
3. You may now release the “SET” button. The blue LED will continue to 
    flash quickly for about 15 seconds. 

Operating Mode

Regular

Flashing Alert

Countdown Timer

Upper LED Indication

Flashes quickly

Flashes slowly

Steadily On

4. Within 15 seconds, follow steps A) to C).
     A). Press the PROG button on the back of the  
         TC transmitter 

.

     B). Press the button on the  TC transmitter that 
          you would like to program. 
     C). Once the transmitter is programmed,  the 
          

 on the 

 flash 

          quickly then stop flashing, indicating you 
          have successfully programmed the trans-
          mitter to the module. Now the programmed 
          transmitter 

with a sharp object.

two blue LEDs

Wall Dimmer

button is ready to be used for 

          Regular Mode.

1. Wall Dimmer must be installed and powered properly. Touch the touch 
    pad. The connected light should be on, and  the 2 blue LEDs are off.
2. Press and hold the "SET" button for about 9  seconds, until the upper
    blue LED flashes slowly.
3. You may now release the "SET" button. The blue LED will continue to
    flash slowly for about 15 seconds.
4. Within 15 seconds, follow steps A to C.
     A. Press the PROG button on the back of  the TC transmitter with a 
           sharp object.
     B. Press the button on the  TC transmitter that you would like to program.
     C. Once the transmitter is programmed,  the two blue LEDs on the Wall 
          Dimmer flash quickly then stop flashing, indicating you have 
          successfully programmed the transmitter to the module. Now the 
          programmed  transmitter button is ready to be used for Flashing Alert 
          Mode.

1. Wall Dimmer must be installed and powered properly. Touch the touch 
    pad The connected light should be on, and  the 2 blue LEDs are off.
2. Press and hold the "SET" button for about 15  seconds, until the upper
    blue LED will be steadily on.
3. You may now release the "SET" button. The blue LED will continue to 
    be on for about 15 seconds.

TM

Thank you for your purchase of a SkylinkHome  lighting receiver, Wall 
Dimmer, Model WR-001.  Simply replace your existing wall switch with this 
Wall Dimmer, you can then wirelessly turn on and off, dim and brighten 

TM 

lights with a SkylinkHome  transmitter. 

The Wall Dimmer WR-001 can communicate with up to 8 transmitters, so 
user has the option to add more transmitters to the system, such as more 
remote controls, or motion sensors etc. 

All wireless signal communications within the 

 System are 

based on rolling code technology to ensure highest security is used. 

The following items are included in this package:

- Wall Dimmer 
- Wire nuts
-  

TM 

SkylinkHome

User’s Instructions

Note:
Antenna ( grey wire) -- Do not cut it, keep it as straight as possible. 
Put the antenna directly  into the dry wall or through a hole of the 
metal box into the dry wall to get more control distance with a remote.