SmartLabs 2458A1 Leaflet

Page 1 of 1 
Rev. 09-20-2011 

 

 

SmartLabs Limited Warranty – SmartLabs warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be 
free from defects in material & workmanship & will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by 
misuse or neglect.   
U.S. Patent No. 7,345,998, International patents pending © Copyright 2010  
SmartLabs, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845  

 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 

Status LED 

Individual commands can be Linked to the On and Off buttons on your Controller. For example, you can Link the door to lock 
when you press the On button and unlock when you press the Off button on your Controller.  
NOTE: LOCK and UNLOCK commands must each be Linked to a separate button. Commands cannot be toggled on one 
button unless you are using a Controller that allows toggle mode (e.g., KeypadLinc

™

).  

To Link to an On button: 
1)  Use the Set button to put your lock into the desired state (what action you would like the lock to perform when you press 

the On button) 

2)  Set your Controller to Linking Mode. (For most Controllers, press & hold an On or Scene button for 10 seconds, or the Set 

button for 3 seconds.) 
You will have 4 minutes to complete the next step before Linking Mode automatically times out. 

3)  Press & hold the Set button on MorningLinc for 3 seconds 

4)  Confirm that Linking was successful by locking/unlocking the door and pressing the On button you just Linked to 

To Link to an Off button: 
1)  Use the Set button to put your lock into the desired state (what action you would like the lock to perform when you press 

the Off button) 

2)  Set your Controller to Linking Mode. (For most Controllers, press & hold an On or Scene button for 10 seconds or the Set 

button for 3 seconds.) 

 

You will have 4 minutes to complete the steps 3 and 4 before Linking Mode automatically times out. 

3)  Double-tap the Set button on MorningLinc and wait for 3 seconds before next step 
4)  Press & hold the Set button on MorningLinc for 3 seconds 

 

5)  Confirm that Linking was successful by locking/unlocking the door and pressing the Off button you just Linked to  

 

MorningLinc

TM

 – INSTEON

®

 Morning Industry 

RF Doorknob/Deadbolt Controller 

MorningLinc consists of a specially-wired ICON Appliance Module, 
which will allow you to lock or unlock your Morning Industry RF 
deadbolts and door locks (up to fifteen) with the press of a button 
on any Linked INSTEON Controller.

When installing MorningLinc, use an outlet or extension cord to keep the unit within five feet of the door lock fixture. Once 
installation is complete, MorningLinc can be moved to another outlet (up to 30 feet away from the door lock fixture). 
1)  Be sure you have properly installed at least two Access Points or other dual-band products. Search for dual-band 

INSTEON products at: 

http://www.smarthome.com/dualband

 

2)  Plug MorningLinc into an unswitched wall outlet 

 

3)  Use a screwdriver to remove the cover plate from the door lock fixture. Then, tap its Set button (labeled “S”). 

4)  Tap the Set button on MorningLinc 

5)  If you wish to control multiple door locks with MorningLinc, repeat steps 3 and 4 with each additional door lock fixture 
6)  Tap the Set button on MorningLinc to toggle the door lock fixture locked and unlocked 

NOTE: The MorningLinc Status LED will follow the last INSTEON command it received. When the door is manually locked/unlocked 
from the keypad or the lock itself, the LED will not change until it receives an INSTEON command (either from a Linked Controller or 
the Set button on MorningLinc). It may take 3-5 seconds for the door lock fixture to respond to INSTEON commands.

Owner’s Manual: 

http://www.smarthome.com/manuals/2458a1.pdf

  

Call: Tech. Support @ 1-800-SMARTHOME (800-762-7846) 
Contact Us Online: 

http://www.smarthome.com/contactus.html

 

Set button