Skylink MD-318 Leaflet

This receiver offers two optional states after powered on, choose the one 
which fits your requirement.

1) You may use the wall switch to control the light as usual. When the 
    wall switch is off, the light is off. When the wall switch is on, the light is 
    on. 

2) After a power outage and the electricity comes back, the light will be 
    on if the wall switch is in On position.

1) A special sequence is needed to turn on the light by the wall switch. 
    To turn on the light by the wall switch: 1) Switch On, 2) Switch Off, 
    3) Switch On again within 2 seconds. Light will be on.

2) After a power outage and electricity comes back, the light will be off 
    under most of the circumstances.
 

To toggle a receiver between these two states, re-program a transmitter 
twice consecutively to the receiver. Referring to Section 3, repeat the 
programming steps twice consecutively with a transmitter that is already 
programmed, the receiver will change state.

Input Voltage: 120VAC , 60Hz   

Maximum Load: 300W at 120VAC 
Operating Frequency: 318MHz

Range: Up to 500 feet in open area

Standby Current: 6mA
Minimum Load: 10W

Operational Temperature: -4° F - 140° F 

(-20° C - 60° C)

Humidity: 5%-95%

The Remote Control is approved by the FCC and it complies with Part 15 of the 
FCC Rules. Its operation is subject to the following two conditions : 
1.  This device may not cause harmful interference.
2.  This device must accept any interference that may cause undesired operation.

WARNING:
Changes or modifications to this unit not expressly approved by the party responsible 
of compliance could void the user’s authority to operate the equipment.

If, within one year from date of purchase, this product should become defective 
(except battery), due to faulty workmanship or materials, it will be repaired or 
replaced, without charge. Proof of purchase and a Return Authorization are required.

You may erase a transmitter from the ON/OFF/Dimming Control, but you 
cannot erase a specific device directly, you must erase all the wireless 
devices, then program the ones you want to keep.  Follow the instructions 
below to erase programmed transmitters.

1. Power off the lighting receiver.  (Switch off the wall switch)

2. Transmit a "Erase" code from the transmitter until step 4.

3. Power up the ON/OFF/Dimming Control (Switch on the wall switch), 
    you will hear a beep.

4. You may stop the "Erase" code signal transmission, the ON/OFF/
    Dimming Control will beep, indicating you have successfully erased all 
    the devices from the ON/OFF/Dimming Control. 

To erase other transmitters / sensors, please refer to the instructions of 
the transmitters / sensors.

The Skylink

 System consists of many other devices such as

SkylinkHome  Remotes, Motion Sensor, ON/OFF Wall Switch, Wall 
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF 
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, 
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit 
Skylink website at www.skylinkhome.com for more information. 

TM

Home

TM

TM  

If you would like to 
· find out the up-to-date specifications
· know more about features and applications
· download documents, i.e. user’s instructions
· order Skylink products 

or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax  (800) 286-1320

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com

P/N. 101Z699
Patent Pending
©2010 SKYLINK GROUP

In case the transmitter is not on hand, you can still operate the lighting 
fixture with the wall switch.