Skylink 838A Leaflet

  

  

re

g

is

te

re

d

 t

ra

d

e

m

a

rk

 o

f 

s

k

y

lin

k

 T

e

c

h

n

o

lo

g

ie

s

 I

n

c

.,

R

  The code Scrambler
Anti-Theft Garage Door
       Remote Control
  Operating Instructions
         (  Model  838A )

(1)  Each transmitter was assigned an 
       individual (never duplicated) code in the
       factory. For the receiver to recognize and
       respond to the transmitter, it must first
       “learn” the code.  With the receiver
       installed in the operator, remove the front
       lower cover of the receiver case, press
       and hold Button 1 on the receiver, (its red
       light will flash), while simultaneously
       pressing and holding Button  A on the 
       transmitter, until the receiver light stops
       flashing indicating it has learned the 
       code.

(2)   Test the new transmitter. If it does not
        operate your garage door, repeat Step 1.

The Code Scrambler  Anti-Theft Garage
Door Remote Control uses an FCC approved
transmitter and receiver, and complies with
part 15 of the FCC Rules. Its operation is
subject to the following two conditions:
1. This device may not cause harmful
     interference.
2. This device must accept any interference
    that may be received, including
    interference that may cause undesired
    operation.

TM

Warning :  Changes or modifications to this
                 unit not expressly approved by
                 the party responsible of
                 compliance could void the user’s
                 authority to operate the
                 equipment.

(3)  To program Button B to operate another
      garage door, repeat Steps 1 & 2 with a
      second receiver (sold separately).

(4)  If you use the transmitter to operate only  
      one door, with either Button A or B,
      repeat Steps 1 & 2, using Button B.

CAUTION : if you press and hold the 
button 1 and button 2 on the receiver and
then release the Button 2 (its red light will
flash faster), this will erase all of the 
“ learned ” codes in its memory. Repeat
the “ learning ” process with each
transmitter. 

Skylink will not be liable or responsible for
any misuse or application of this product
other than for its intended use.

CUSTOMER SERVICE
17  Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email: support@skylinkhome.com
Customer Service : (800) 304-1187
From 9am to 5pm EST (Mon-Fri)
http://www.skylinkhome.com
P/N.101A366
Patent no. D382251, D380895
   2005 SKYLINK GROUP

C

(1) Your receiver is an universal radio digital
     receiver:
     Operating voltage is from 18V to 30V 
      AC or DC supplied by the garage or 
      gate operator.

(2)  Wiring connection:
       White wire - connect to common.
        Red wire - connect to 24V
        Black Wire - relay output, connect to relay
     
(3)   Antenna wire:
       Please DO NOT remove the yellow wire,
       ensure that it is in up-right position to
       receive data signals from the transmitter.

(1)  Operating source :
       Operated by 12 Volt “ cigarette lighter ”
        type (size 23A) Alkaline battery
        (included)

(2)   Battery replacement :
        Remove the battery cover, then install a
        new battery when LED dim. Then
        replace the battery cover after the 
        installation.

BUTTON 1

Red Light

BUTTON 2

If, within one year from date of purchase,
this product should become defective
(except battery), due to faulty workmanship
or materials, it will be repaired or replaced,
without charge, Proof of purchase is 
required.

Warning ! Do not let children use the
garage door transmitter without adult
supervision. Children can injure
themselves or others the garage door.

RED

BLACK

WHITE