Russound ST2S User Manual
36
NOTE: The CAV6.6 (Rev. 3) must have firmware version 2.01.16 or higher,
CAV6.6 (Rev. 4) must have firmware version 3.01.10 or higher,and UNO-S2
firmware must be version 3.01.01 or higher to control the ST2S Tuner. Use the
System Info Menu of the CAV6.6 to check the firmware version. If the firmware is
not the proper revision as noted here, visit the Document Center at
www.russound.com to obtain the latest version.
CAV6.6 (Rev. 4) must have firmware version 3.01.10 or higher,and UNO-S2
firmware must be version 3.01.01 or higher to control the ST2S Tuner. Use the
System Info Menu of the CAV6.6 to check the firmware version. If the firmware is
not the proper revision as noted here, visit the Document Center at
www.russound.com to obtain the latest version.
To Program the CAV6.6 to operate with the ST2S Tuner:
(refer to the CAV6.6 Instruction Manual for details)
(refer to the CAV6.6 Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the
UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (SIR-
IUS) is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or SIRIUS). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the
UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (SIR-
IUS) is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or SIRIUS). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note:
When the ST2S Tuner is used with the CAV6.6 or other RNET controller, it is configured as an RNET
command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave as a
fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique source
number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Each of the ST2S modules can be configured as source number “unassigned” if the module is used
in another system (e.g., home theater) or will not be used as a source in the RNET system.
When the ST2S Tuner is used with the CAV6.6 or other RNET controller, it is configured as an RNET
command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave as a
fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique source
number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Each of the ST2S modules can be configured as source number “unassigned” if the module is used
in another system (e.g., home theater) or will not be used as a source in the RNET system.
Key Function Note:
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” com-
mand type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and
will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” com-
mand type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and
will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.
ST2S TUNER PROGRAMMING
PROGRAMMING FOR CAV6.6 USE