Revolabs 10-FLX2-200-VOIP 10-FLX2-020-VOIP 10-FLX2-002-VOIP 10-FLX2-101-VOIP User Manual
74
Troubleshooting
Warning Messages
Speaker / Microphone Link Lost
If a FLX Microphone or FLX Speaker loses connection to the FLX2 Base Station, the
LED indicator will begin flashing a sequence of red – yellow - green - yellow and start
emitting a beeping notification. To reconnect the Microphone or Speaker move it back
into range of the Base Station.
Speaker/Microphone Low Battery
If a FLX Microphone or FLX Speaker begins to experience a low battery, the LED
indicator will begin to flash a green - yellow (unmuted) or red - yellow (muted)
sequence. It will also start to emit an audio signal. When this LED and sound sequence
begins, the battery has roughly 5% battery power remaining and should be returned to
the Charger Base.
Speaker/Microphone Off
If the FLX Microphone or FLX Speaker suddenly turns off, it is the result of two possible
causes.
If a FLX Microphone or FLX Speaker loses connection to the FLX2 Base Station, the
LED indicator will begin flashing a sequence of red – yellow - green - yellow and start
emitting a beeping notification. To reconnect the Microphone or Speaker move it back
into range of the Base Station.
Speaker/Microphone Low Battery
If a FLX Microphone or FLX Speaker begins to experience a low battery, the LED
indicator will begin to flash a green - yellow (unmuted) or red - yellow (muted)
sequence. It will also start to emit an audio signal. When this LED and sound sequence
begins, the battery has roughly 5% battery power remaining and should be returned to
the Charger Base.
Speaker/Microphone Off
If the FLX Microphone or FLX Speaker suddenly turns off, it is the result of two possible
causes.
1. The battery has completely depleted and should be returned to the charger until
it is fully charged again.
2. The Microphone or Speaker lost connection with the Base Station for more than
10 minutes and therefore shut down. It should be returned into reach of the Base
Station and switched on again to be reactivated.
Station and switched on again to be reactivated.
Dialer Low Battery
When the Dialer experiences a low battery it will display a ‘low battery’ notification on
the screen. The Dialer should be returned to the charger until the battery status on the
home screen shows a full charge.
Dialer Link Lost
If the FLX Dialer loses connection to the FLX2 Base Station it will display a ‘connection
lost’ notification on the screen and starts emitting a warning sound. The Dialer should
be moved back into range of the Base Station at which point it will reconnect
automatically.
Base Power Lost
If the FLX2 Base Station loses power, it will disconnect all telephone calls, analog audio
inputs/outputs and will disconnect from the FLX Dialer, Speaker, and Microphones.
Check to make sure that the power adapter is still connected to the FLX2 Base Station.
Once the FLX2 Base Station is powered back on, the Dialer, Speaker and Microphones
will reconnect automatically.
When the Dialer experiences a low battery it will display a ‘low battery’ notification on
the screen. The Dialer should be returned to the charger until the battery status on the
home screen shows a full charge.
Dialer Link Lost
If the FLX Dialer loses connection to the FLX2 Base Station it will display a ‘connection
lost’ notification on the screen and starts emitting a warning sound. The Dialer should
be moved back into range of the Base Station at which point it will reconnect
automatically.
Base Power Lost
If the FLX2 Base Station loses power, it will disconnect all telephone calls, analog audio
inputs/outputs and will disconnect from the FLX Dialer, Speaker, and Microphones.
Check to make sure that the power adapter is still connected to the FLX2 Base Station.
Once the FLX2 Base Station is powered back on, the Dialer, Speaker and Microphones
will reconnect automatically.
Microphone, Speaker, or Dialer not connecting to Base Station
If any of the components of the FLX2 Conference Phone indicate that they are
searching for the Base Station, or lost the connection to the Base Station, please follow
these steps:
searching for the Base Station, or lost the connection to the Base Station, please follow
these steps:
1. Is the Base Station powered up – the Status LED on the back of the Base Station
should have green double flashes about every second. If not, please power up