RCA MAF80BK Leaflet

Follow these precautions to ensure safe installation and 

mounting of your flat panel TV.

  Make sure these instructions are read and completely 

understood before attempting installation. If you 

are unsure of any part of this installation, contact a 

professional installer for assistance.

  The wall or mounting surface must be capable of 

supporting the combined weight of the wall mount and 

the display; otherwise the structure must be reinforced.

  Protective eye wear and proper tools must be used. 

A minimum of two people are required for this 

installation. Failure to use safety gear and/or attempting 

this installation alone can result in property damage, 

serious injury, or death. 

   Follow all instructions and recommendations regarding 

adequate ventilation and suitable locations for mounting 

your display in the owner‘s manual for your display.

 

Be sure you have purchased the correct wall mount  

for your TV. Recheck the size and weight constraints.

  Gather all necessary tools before you begin 

installation. You will need a #3 bit Phillips screwdriver, 

electric drill, drill bit (included), level (integrated level 

on product), stud finder, and hammer (for brick and 

concrete installations).

  It is essential for the wall mount plate to be attached 

to wall studs. (Use a stud finder.)

  Use the included hardware for mounting purposes. 

This hardware has been provided to ensure a safe and 

secure mount.

  Hire a licensed electrician to relocate an electrical 

outlet, if needed.

  Be sure to purchase wires long enough to connect 

the TV to the audio and video components in your 

installation.

Keep your sales receipt to obtain warranty parts and 

service and for proof of purchase. Attach it here and record 

the model number. This number is located on the product.

Model No. __________________________________________

Purchase Date: ______________________________________

Dealer/Address/Phone  ________________________________

Model: 

MAF80BK 

 

Two-piece, low-profile design

Description: 

RCA Universal Flat Panel TV 

 

Wall Mount

TV Size Range: 

37" – 60"

Maximum Load: 

165 lbs. (74.8kg)

Minimum Profile: 

3.1" (7.9 cm)

Tilt: 

+/- 0-15°

Universal VESA Compatibility
Integrated Bubble Level
Cord Management

Before beginning the installation process, verify that you 

have all the necessary tools on hand. The following tools 

are required for proper installation:

  #3 bit Phillips screwdriver
  Stud finder
  Electric drill
  Drill bit (included)
  5/16" (8mm) masonry drill bit for concrete/ 

      brick installation

  Level (integrated level on product)
  Hammer (for concrete installations)

Audiovox Electronics Corporation (the “Company”) warrants to you the 

original retail purchaser of this product that should it, under normal use 

and conditions, be proven defective in material or workmanship during 

its lifetime while you own it, such defect(s) will be repaired or replaced (at 

the Company’s option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the 

product is to be delivered with proof of warranty coverage (e.g. dated bill 

of sale), specification of defect(s), transportation prepaid, to the Company 

at the address shown below. Do not return this product to the Retailer.

This  Warranty  does  not  cover  product  purchased,  serviced  or  used 

outside the United States or Canada.

This Warranty is not transferable and does not extend to costs incurred for 

installation, removal or reinstallation of the product. This Warranty does 

not apply if in the Company’s opinion, the product has been damaged 

through alteration, improper installation, mishandling, misuse, neglect, 

or accident.

THE  EXTENT  OF  THE  COMPANY’S  LIABILITY  UNDER  THIS 

WARRANTY  IS  LIMITED  TO  THE  REPAIR  OR  REPLACEMENT 

PROVIDED  ABOVE  AND,  IN  NO  EVENT,  SHALL  THE  COMPANY’S 

LIABILITY  EXCEED  THE  PURCHASE  PRICE  PAID  BY  PURCHASER 

FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY 

IMPLIED  WARRANTIES,  INCLUDING  ANY  IMPLIED  WARRANTY 

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE 

SHALL BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE 

SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR 

INCIDENTAL DAMAGES WHATSOEVER. No person or representative is 

authorized to assume for the Company any liability other than expressed 

herein in connection with the sale of this product.

Some states/provinces do not allow limitations on how long an implied 

warranty lasts or the exclusion or limitation of incidental or consequential 

damage so the above limitations or exclusions may not apply to you. This 

Warranty  gives  you  specific  legal  rights  and  you  may  also  have  other 

rights which vary from state/province to state/province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd.,  

Hauppauge, New York  11788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, 

Unit 3, Door 16, Mississauga, Ontario  L5T 3A5
Trademark(s)  Registered,  Marques  Deposee,  Marcas  Registradas. 

All  other  brands  and  product  names  are  trademarks  or  registered 

trademarks of their respective owners.
© 2008 Audiovox Accessories Corporation 

111 Congressional Blvd., Suite 350 

Carmel, IN 46032

Thank you for choosing the RCA MAF80BK Universal 

Flat Panel TV Wall Mount. This mount can be used for all 

major brands of 37" - 60" flat panel TVs, 165 lbs (74.8 kg) or 

under. This wall mount features a 0-15-degree tilt for easy 

viewing. Before attempting to mount your television set, 

please remove all parts from this package and read the 

installation instructions carefully.

(Ref) Item (Qty)

Bag #

(A) M4x12 Bolt (x4)

(B) M4x30 Bolt (x4)

(C) M4 Lock Washer (x4)

(D) M5x12 Bolt (x4)

(E) M5x30 Bolt (x4)

(F) M5 Lock Washer (x4)

(G) M6x12 Bolt (x4)

(H) M6x35 Bolt (x4)

(I) M6 Lock Washer (x4)

(J) M8x16 Bolt (x4)

(K) M8x40 Bolt (x4)

(L) M8 Lock Washer (x4)

(M) Small Spacer (x4)

(N) Large Spacer (x4)

(O) M6 Washer (x4)

(P) Concrete Anchor (x6)

(Q) M8x63 Hex Bolt (x6)

(R) Hex Bolt Washer (x6)

(S) Drill Bit (1)

Fig. 1

Attach the wall plate to the wall.

the wall plate to the wall.

 For safety, this mount must be secured to 

two adjacent wood studs no less than 16” apart.

   Using a stud finder, locate and mark two adjacent studs 

for securing the mount. 

   Place the wall plate against the wall and level it using 

the bubble guide.

   Mark four locations (two per stud) on the wall where 

the mount will be secured. Be sure to use the center of 

each stud.

   Remove the wall plate and drill a 1/4“ (6 mm) pilot hole 

at each location using an electric drill.

   With the help of another person, replace the wall 

plate and level it using the bubble guide. Fix it to the 

wall using the Lag Bolts (Q) and Lag Bolt Washers (R) 

provided (Fig. 1).

  Do not over-tighten the bolts and do not release the 

wall plate until all screws are secure.

  Attach the cable manager to the middle of the top 

crossbar (Fig. 2).

Fig. 2

Attach the 

cable manager

to the top 

crossbar.

   Place the wall plate against the wall and level it using 

the bubble guide.

   With the help of another person, mark off six (6) 

locations for fixing the mount to the wall.

  Place the wall plate aside and drill a hole at each 

location using a 5/16” (8 mm) masonry bit. Remove any 

excess dust from the holes.

   Insert one Concrete Anchor (P) into each hole. A 

hammer can be used to lightly tap the anchors into 

place if necessary.

   With the help of another person, replace the wall 

plate and level it using the bubble guide. Fix it to the 

wall using the Lag Bolts (Q) and Lag Bolt Washers (R) 

provided (Fig. 1).

   Do not over-tighten the screws and do not release the 

wall plate until all screws are secure.

    Attach the cable manager to the middle of the top 

crossbar (Fig. 2).

   Examine the back of your television. If the back of your 

display is flat, you will be using one of the shorter bolts 

from the hardware kit. If the back of your display is 

curved or recessed, you will be using one of the longer 

bolts and a spacer (Fig. 4).

Fig. 3

Attach the arms to the back

of your display.

 

 Use extra 

care during this part of the 

installation. Avoid laying your 

display face down if possible 

as it may damage the viewing 

surface.

  Determine the correct diameter bolt to use by trying 

one bolt each from Bags 1 - 4 of the hardware kit. Do 

not force any of the bolts – if you feel resistance stop 

immediately to avoid damaging your display.

   Attach the arms to the back of your display 

using the bolts identified in Steps 1 and 2 and the      

corresponding Lock Washer (C, F, I, or L) (Fig. 4). You 

will need to use the M6 Washers (O) if you are using 

the M4, M5, or M6 bolts. If your display has a curved or 

recessed back, you may also need to use a Spacer (M or 

N). 

  Make sure the screws are snug, but do not over-tighten.

For displays with flat

backs...

For displays with curved

or recessed backs...

Fig. 4 - Use a longer bolt and spacer for displays with curved or recessed 

backs. Do not use the M6 Washer (O) if you are using the M8 Bolts (J or K).

   With the help of another person, carefully lift your 

display and place it on the wall plate (Fig. 5). Do not 

release the display until the mounting arms have 

securely hooked onto the crossbars!

   Move the safety tab located on each arm into position 

to avoid having the display accidentally lifted from the 

mount. A padlock can be inserted into one of the tabs 

to help prevent theft of your display (Fig. 6).

Fig. 5

Carefully hook the 

display onto the wall plate.

Fi 5

  The cable manager can be used to keep your power 

cord and other A/V cables in order.

   To adjust the tilt position, have one person hold the 

display in position while another person loosens the 

two tilt adjustment knobs located on either side of 

the wall plate (Fig. 7). Once the knobs are loose, move 

the display to the desired angle. Re-tighten the knobs 

before releasing the display.

Fig. 6

A small padlock 

can be used to help

prevent theft of 

your display 

(padlock not 

included).

Fig. 7

Loosen the 

adjustment knobs 

to change the tilt 

angle. There is one 

knob on each side

of the mount.