Rangemaster 90 CERAMIC U109650-02 User Manual
29
SERVICING - WARNING
Disconnect from the electricity before servicing. Check appliance is safe when you have finished.
11. To Change Oven Door Outer Panel
Remove the two plastic blanking plugs from the door
handles. Remove the 4mm Hex headed screws holding the
handle to the door with the hexagon key tool. Remove two
screws from top edge and two from bottom edge of the
door.
handles. Remove the 4mm Hex headed screws holding the
handle to the door with the hexagon key tool. Remove two
screws from top edge and two from bottom edge of the
door.
Remove outer door panel. Fit door handle to new panel. Fit
the plastic blanking plugs to the fixing holes.
the plastic blanking plugs to the fixing holes.
The handles should be above the fixings.
Fit panel to door. If replacing the outer panel on the right
hand door (with the Thermodial) take care to make sure the
sensor of the Thermodial is sealed to the door by the rubber
grommet.
Fit panel to door. If replacing the outer panel on the right
hand door (with the Thermodial) take care to make sure the
sensor of the Thermodial is sealed to the door by the rubber
grommet.
Reassemble in reverse order.
7. To Remove a Thermostat
Lift up the ceramic hob top (see 2). Remove control panel
(see 4). Open appropriate oven door and remove oven
furniture.
(see 4). Open appropriate oven door and remove oven
furniture.
Right hand oven
Remove thermostat phial cover (2 screws). Unclip the
thermostat phial from the clips in the oven back.
thermostat phial from the clips in the oven back.
Left hand oven
Pull cooker forward to gain access to the cover box at
the rear of the cooker. Remove the screws securing the
cover and lift clear.
the rear of the cooker. Remove the screws securing the
cover and lift clear.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned
between the clips.
Check operation of thermostat.
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned
between the clips.
Check operation of thermostat.
8. To Change Grill Controller
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for correct
operation.
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for correct
operation.
9. To Remove Grill Outer Door Panel
Open left hand oven door and remove 2 screws from
bottom edge of grill door. Open grill door, support grill door
outer panel and remove two screws from top inner face of
grill door.
Reassemble in reverse order.
bottom edge of grill door. Open grill door, support grill door
outer panel and remove two screws from top inner face of
grill door.
Reassemble in reverse order.
10. To Remove an Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free.
Door is heavy - take care. Open the oven door. Loosen the
two top hinge screws.
by springing one side out of the bracket on the door and
sliding the other side free.
Door is heavy - take care. Open the oven door. Loosen the
two top hinge screws.
Support the weight of the door and remove the screw
nearest the hinge pin. Swing the hinge up and away from
the hinge pin on the door.
Lift the door away from the bottom hinge.
Re-assemble in reverse order.
When replacing the door ensure that the nylon hinge bush
is in position between the hinge pin and the hinge bracket
at the both the bottom and top.
nearest the hinge pin. Swing the hinge up and away from
the hinge pin on the door.
Lift the door away from the bottom hinge.
Re-assemble in reverse order.
When replacing the door ensure that the nylon hinge bush
is in position between the hinge pin and the hinge bracket
at the both the bottom and top.