Radio Shack 61-2117 User Manual
©
2003 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
61-2117
OWNER’S MANUAL — Please read before using this equipment.
Thank you for purchasing the RadioShack
Two Bell Wireless Door Chime. It works as a
doorbell, a remote pager, or an alert. You
can add an optional external sensor to have
a chime that alerts you when someone
walks into a room. The wireless door
chime’s three-position channel switch
prevents other transmitters or radio devices
from sounding the chime.
Two Bell Wireless Door Chime. It works as a
doorbell, a remote pager, or an alert. You
can add an optional external sensor to have
a chime that alerts you when someone
walks into a room. The wireless door
chime’s three-position channel switch
prevents other transmitters or radio devices
from sounding the chime.
MOUNTING THE
RECEIVER
O
N
A
F
LAT
S
URFACE
Pull out the wire stand on the back of the
receiver and set it on a table or other flat
surface.
receiver and set it on a table or other flat
surface.
O
N
A
W
ALL
1. Drill one
3
/
16
-inch diameter hole and
insert one of the supplied anchors.
2. Drive the supplied M3.5 screw into the
hole until the screw's head extends
about
about
1
/
8
inch from the wall.
3. Align the keyhole slot on the bottom of
the receiver with the screw in the wall,
then slide it down to secure it.
then slide it down to secure it.
MOUNTING THE
TRANSMITTER
1. Remove the transmitter from the holder.
2. Use the holder as a template to mark
two screw holes on the wall.
3. Remove the holder from the mounting
surface and drill two
1
/
4
inch diameter
holes. Insert one of the supplied
anchors into each hole.
anchors into each hole.
4. Drive a screw through the holders.
5. The transmitter can be slid in and out of
the holder. To lock the transmitter in the
holder, fix it with a size M2.6 screw at
the bottom of the holder.
holder, fix it with a size M2.6 screw at
the bottom of the holder.
INSTALLING
BATTERIES AND
SELECTING CHANNELS
The wireless door chime requires three AAA
size batteries in both transmitters and three
C size batteries in the receiver. For best
performance and longest life, we
recommend RadioShack alkaline batteries.
size batteries in both transmitters and three
C size batteries in the receiver. For best
performance and longest life, we
recommend RadioShack alkaline batteries.
I
N
THE
T
RANSMITTER
1. Slide the transmitter's battery
compartment door in the direction of the
arrow to remove it.
arrow to remove it.
2. Use a small flat-blade screwdriver to
slide the switch inside the battery
compartment to the desired channel for
the transmitter.
compartment to the desired channel for
the transmitter.
Receiver
Transmitter (two included)
Slide ON/OFF to
ON so that when
BELL is pressed
on one of the
transmitters, a
door chime
sounds.
ON so that when
BELL is pressed
on one of the
transmitters, a
door chime
sounds.
Indicator — Lights
when BELL is
pressed.
when BELL is
pressed.
BELL — Press
BELL to hear the
door chime.
BELL to hear the
door chime.
!
IMPORTANT
!
If an icon appears at the end of a paragraph,
go to the box on that page with the
corresponding icon for pertinent information.
go to the box on that page with the
corresponding icon for pertinent information.
o
— Warning
Ó
— Hint
— Caution
Ô
— Note
!
— Important
CAUTION
• Use only fresh batteries of the required size
and type. Always remove old or weak
batteries. They can leak chemicals that
destroy electronic circuits
batteries. They can leak chemicals that
destroy electronic circuits
• Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.
rechargeable), or rechargeable batteries of
different capacities.
Two Bell Wireless Door Chime