Philex RC026SP User Manual

The RCx4 has 4 Device Modes (TV, VCR, SAT & DVD)  
Your RCx4 can be set-up either by entering the appropriate codes from the list 
of codes supplied or by using either the Auto or Manual code search facility. 
Instructions for all three methods follow. 

Probably the easiest way to set-up your RCx4 for most devices, especially 
if there are a lot of codes listed for your particular brand, is by Auto Code 
Search.

TV SETUP BY AUTO CODE SEARCH
1.  Turn on your TV
2. Hold down both 

POWER and 

MUTE keys on your RCx4 

     simultaneously until the STATUS INDICATOR LED lights up and stays red 
      (about 4 seconds).

3.  Release the  POWER and 

MUTE keys The STATUS INDICATOR should 

     still be lit. If not repeat step 2.
4.  Press the TV DEVICE INDICATOR key once. The STATUS INDICATOR and the 
     DEVICE INDICATOR should now both be lit RED.  

5.  To search, aim your RCx4 at your TV.
6.  Hold down the power key for about 8 seconds until the STATUS INDICATOR 
      lights up.
7.  The STATUS INDICATOR will repeatedly flash twice then remain unlit for 
      1 second, flash twice and remain unlit for 1 second. The DEVICE INDICATOR 
      key will also flash repeatedly.
8.  When a suitable code is found the TV will switch off. When the TV switches 
     off the TV DEVICE INDICATOR key must be pressed immediately to store 
      the correct code (Please Note: if the TV DEVICE INDICATOR key is not 
      pressed immediately the search will continue).
9.  Now press the POWER key. If the TV switches on the code has been stored 
     and you can check that other functions work properly.
10.To stop the Auto Code Search at any time press any key and the remote will 
      go to Manual Code Search.
If you are unable to find a correct code or cannot store the code fast enough 
try finding the code either using Manual Code Search or by using Setup by 
Entering Device Code

VCR, SAT/CTV & DVD SETUP BY AUTO CODE SEARCH 
Simply turn on your VCR, SAT/CTV or DVD and repeat the above procedure to 
search for the Device Codes for your VCR, SAT/CTV or DVD but instead of the 
TV DEVICE INDICATOR key press either the VCR, SAT or DVD DEVICE INDICATOR 
key in steps 4 & 8.

(Note: If no keys are pressed on the RCx4 for a period longer than 10 seconds 
during set-up, the RCx4 will automatically exit the set-up process and revert to 
the last entered code. This feature reduces accidental erasure of your codes)

1.  Turn on your TV
2. Look up the brand name of your TV in the DEVICE CODE LIST 
      (See pages 7-11).
3.  Look up the 3-digit Device Code next to the brand name of your 
     equipment. If there is more than one code listed for your brand, start with 
     the first code listed and follow the instructions below:
4. Hold down both 

POWER and 

MUTE keys on your RCx4 

     simultaneously until the STATUS INDICATOR LED lights up and stays red 
      (about 4 seconds).

5.  Release the  POWER and 

MUTE keys. The STATUS INDICATOR LED 

     should still be lit. If not repeat step 4.
6.  Press the TV DEVICE INDICATOR key once. The STATUS INDICATOR LED and 
     the DEVICE INDICATOR should now both be lit. 

7.  Use the number keys on your RCx4 enter the 3-digit Device Code. If you 
     have entered a valid code, the STATUS INDICATOR will blink once. If you 
     have entered a wrong code, the STATUS INDICATOR will blink twice. 

8.  Try the keys on your RCx4 that correspond to similar keys on your original 
      remote control, especially those you use most. (Note that the RCx4 will exit 
     the set-up procedure if you do not press any keys on the RCx4 for more 
      than 10 seconds). If your TV works on all or most of the keys on your RCx4, 
     you have entered a suitable Device Code. Go to step 11. (Note: Your RCx4 
     will only operate functions controlled by your original remote nor are the 
       supplied codes guaranteed to operate all these functions) 
9.  If the Device Code does not work properly on your TV, press the TV 
     INDICATOR KEY once. The STATUS INDICATOR LED will flash briefly, and 
     remain lit. The TV INDICATOR key should still be RED. (If either of the 
     indicators switch off whilst you are still programming your RCx4, you 
     should start again from step 3.)
10.Repeat steps 7-9 with the other codes listed for your brand of TV until your 
      RCx4 operates most or all of the functions that correspond with the keys on 
      your original remote control.