Pelco pelco time-lapse vcr c649m User Manual
Pelco Manual C649M (7/99)
23
Figure 11.
Timer Program Illustration
(program number)
This number identifies the program. If
the recording times of two programs
overlap, the higher program number has
priority.
the recording times of two programs
overlap, the higher program number has
priority.
DW
Day of the week. DAY is used to record
at the same time every day. SPL (spe-
cial) uses the start/end days selected
with SPECIAL DW at the bottom of the
screen.
at the same time every day. SPL (spe-
cial) uses the start/end days selected
with SPECIAL DW at the bottom of the
screen.
START/END
The VCR uses a 24-hour display. 00:00
indicates midnight; 12:00, noon; and 15:00,
3 p.m.
indicates midnight; 12:00, noon; and 15:00,
3 p.m.
HR
This is the recording mode. SKIP indi-
cates that timer recording is not performed
during the set period. In 2H, 6H, L18H, and
L24H mode, audio is also recorded.
cates that timer recording is not performed
during the set period. In 2H, 6H, L18H, and
L24H mode, audio is also recorded.
6.7 RECORDING SET UP MENU
ALARM REC
Sets the alarm recording time mode. When you turn the JOG
MODE
dial, the display switches in the following order: 2H, 6H, L18H,
L24H, 2H. (Refer to Section 8.3.3 for programming instruc-
tions.) The default is 6H.
L24H, 2H. (Refer to Section 8.3.3 for programming instruc-
tions.) The default is 6H.
ALARM REC
Sets the length of the alarm recording period. When you turn the
DURATION
JOG dial, the display switches in the following order: 1M
(minute), 2M, 5M, 10M, MAN1, MAN2, 15S (second), 30S, 45S,
1M. (Refer to Section 8.3.3 for programming instructions.) The
default is 1M.
(minute), 2M, 5M, 10M, MAN1, MAN2, 15S (second), 30S, 45S,
1M. (Refer to Section 8.3.3 for programming instructions.) The
default is 1M.
EMERGENCY
Sets the emergency recording mode, as follows:
REC
•
OFF – Starts alarm recording when the alarm signal is
received during recording.
received during recording.
•
ON – Starts alarm recording when the alarm signal is
received, not only during recording but also when the
power is OFF or when the tape is stopped.
received, not only during recording but also when the
power is OFF or when the tape is stopped.
The default is OFF. (Refer to Section 8.3.3 for programming
instructions.)
instructions.)
Figure 12.
Recording Set Up
Menu
NOTE:
Set the ALARM REC DU-
RATION to MAN2 to use with the
MX4000 Series Genex™ Multi-
MX4000 Series Genex™ Multi-
plexer.
NOTE: When using the MX4000
Series Genex™ Multiplexer, make
Series Genex™ Multiplexer, make
sure the EMERGENCY REC set-
ting is ON if the VCR is to record
ting is ON if the VCR is to record
alarms only.
6.6 TIMER PROGRAM MENU
Day of the
week
week
<TIMER PROGRAM>
DW START END HR
1 - - -
- - : - -
- - : - - - - -
2 DAY 08 : 40 17 : 25 L18EP
3 MON 22 : 00 22 : 50 72EP
4 WED 22 : 00 22 : 50 96EP
5 SPL 20 : 30 23 : 30 2SP
6 MON 10 : 10 11 : 15 SKIP
7 SUN 23 : 30 00 : 15 6EP
8 MON 21 : 00 21 : 54 2SP
SPECIAL DW MON-FRI
Program
number
number
Recording start time
Next day indicator
Recording end time
Recording mode display
)
<RECORDING SET UP>
2H
1M
OFF
NORMAL<SP>
1
SHOT
ALARM REC MODE
ALARM REC DURATION
EMERGENCY REC
REC MODE
ONESHOT•FIELD
ONESHOT•INTERVAL