Pelco Matrix Switcher/Controller CM6800E-48X8 User Manual
C1528M-F (6/05)
35
CONNECTING A 96 X 16 SYSTEM
1.
Install each CM6800E-48X8 unit and connect appropriate devices to each unit. Note that the CM6800E-48X8 expansion unit must be
installed within three feet of the CM6800E-48X8 main unit.
installed within three feet of the CM6800E-48X8 main unit.
NOTE: If you expand a 48 x 8 system to a 96 x 16 system, you must verify that each CM6800E-48X8 unit contains the same level of
switcher software. Refer to
switcher software. Refer to
Upgrade CM6800 Switcher Software in the Appendix. If you have previously used the CM6800-MGR
software in a 48 x 8 configuration, you must uninstall and then reinstall the software before you can use it in a 96 x 16 configuration.
Refer to the CM6800-MGR Installation/Operation manual, or the CM6800-MGR online help for instructions.
Refer to the CM6800-MGR Installation/Operation manual, or the CM6800-MGR online help for instructions.
Note that keyboards, Genex multiplexers, and other peripheral devices can only be connected to the main unit. The expansion unit
can only support cameras, PTZ receivers, monitors, local alarms, and local relays. Refer to the sample CM6800E 96 x 16 system
shown in Figure 2.
can only support cameras, PTZ receivers, monitors, local alarms, and local relays. Refer to the sample CM6800E 96 x 16 system
shown in Figure 2.
2.
Connect the CM6800E-48X8 expansion unit to the CM6800E-48X8 main unit.
In the following steps, use the cables and clips provided with the CM6800E-KIT.
a.
Attach the spring clips to the bay-to-bay video port on each
CM6800E-48X8 unit.
CM6800E-48X8 unit.
b.
Use the 16-channel video ribbon cable to connect the bay-to-bay video
port on the CM6800E-48X8 expansion unit to the bay-to-bay video
port on the CM6800E-48X8 main unit. The “key” on the cable
connector must be up. Use the spring clips to hold the cable connector
in place.
port on the CM6800E-48X8 expansion unit to the bay-to-bay video
port on the CM6800E-48X8 main unit. The “key” on the cable
connector must be up. Use the spring clips to hold the cable connector
in place.
c.
Use the reversed data cable to connect port 2 on the CM6800E-48X8
expansion unit to port 2 on the CM6800E-48X8 main unit.
expansion unit to port 2 on the CM6800E-48X8 main unit.
Figure 28. Data and Video Connections Between CM6800E-48X8 Units
3.
After completing system installation and power-up, select 96 x 16 as the System setting in programming mode. Refer to the
Programming section.
Programming section.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
8
7
6
5
48
47
46
45
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
41
42
43
44
4
3
2
1
ALT
120/230~
50/60 HZ
50/60 HZ
25 WATTS
1 2 3 4 5 6 7 8
CONTROL
A T
+
T
-
R
+
R
-
T
+
T
-
R
+
R
-
B
1
2
F
3
HZ
75
1
010101
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
8
7
6
5
48
47
46
32
31
30
29
28
27
26
42
43
44
4
3
2
1
ALT
120/230~
50/60 HZ
50/60 HZ
25 WATTS
1 2 3 4 5 6 7 8
CONTROL
A T
+
T
-
R
+
R
-
T
+
T
-
R
+
R
-
B
1
2
F
3
1
010101
CM6800E-48X8 MAIN UNIT
CM6800E-48X8 EXPANSION UNIT
!