Pelco Electronic Keyboard C586M User Manual
14
Pelco Manual C586M (9/99)
Table C. Operation Guide
NOTE:
References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two
modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to Table D) or by
addressing the cameras in groups of 9 or 16 according to the multiplexer they are connected to (switch 7 OFF); for example,
multiplexer 1, cameras 1-9 or 1-16; multiplexer 2, cameras 1-9 or 1-16, etc.
addressing the cameras in groups of 9 or 16 according to the multiplexer they are connected to (switch 7 OFF); for example,
multiplexer 1, cameras 1-9 or 1-16; multiplexer 2, cameras 1-9 or 1-16, etc.
OPERATION
KEYBOARD COMMAND
RESULT
1. Press the MAIN MONITOR key. The green LED over the
MAIN key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a. On the number pad, press the address number of the
a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a
multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays
the address.
multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays
the address.
b. On the number keypad press the number of the
camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON)
On the number keypad press the number of the camera,
then press the CAM key. Refer to Table D for camera
numbers.
On the number keypad press the number of the camera,
then press the CAM key. Refer to Table D for camera
numbers.
3. Press the LIVE/VCR key to select the mode of operation.
1. Press the SPOT MONITOR key. The green LED over the
SPOT key lights.
2. Select the camera.
Addressing by Multiplexer (Switch 7 OFF)
a. On the number pad, press the address number of the
a. On the number pad, press the address number of the
multiplexer (1-16 if the keyboard is connected to a
multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays
the address.
multiplexer; 1-8 if the keyboard is connected to a
server), then press the UNIT key. The LED displays
the address.
b. On the number keypad press the number of the
camera (1-16), then press the CAM key.
Addressing Consecutively (Switch 7 ON)
On the number keypad press the number of the camera,
then press the CAM key. Refer to Table D for camera
numbers.
On the number keypad press the number of the camera,
then press the CAM key. Refer to Table D for camera
numbers.
1. Go to the Advanced System Setup menu.
2. Move the joystick so the cursor highlights SPOT
MONITOR DISPLAY items.
3. Press the OPEN key until TRACK MAIN is displayed.
4. Exit the Advanced System Setup menu.
Call a camera to the
MAIN monitor.
MAIN monitor.
Call a camera to the
SPOT monitor.
SPOT monitor.
Set main tracking.
(Continued on next page)
Stops a sequence if one is in
progress. Displays the camera on
the MAIN monitor.
progress. Displays the camera on
the MAIN monitor.
Displays the camera on the SPOT
monitor.
monitor.
Spot monitor follows the camera
switching that occurs on the main
monitor in single screen mode. In
multi-screen mode, the spot
monitor switches to camera 1.
switching that occurs on the main
monitor in single screen mode. In
multi-screen mode, the spot
monitor switches to camera 1.
Allows only P/T/Z control while in
main monitor mode. Press the
SPOT key to have presets and
patterns while in this mode.
main monitor mode. Press the
SPOT key to have presets and
patterns while in this mode.