Panasonic Attune Operating Guide
17
SW#8: This switch selects RF Power.
ON: Reduce Power
OFF: Full power
OFF: Full power
■ ID Registration
1. Press the ID Registration of the center module for 2 sec-
onds or more. The system is changed to the ID
Registration mode.
Registration mode.
2. While holding down the T1 and T2 buttons simultaneous-
ly, hold down the power button to turn on the headset.
The headset enters the ID Registration setting mode
where the indicators and buttons have different func-
tions than in normal operation. You will hear "ID
Registration Mode" and the power indicator will blink yel-
low.
The headset enters the ID Registration setting mode
where the indicators and buttons have different func-
tions than in normal operation. You will hear "ID
Registration Mode" and the power indicator will blink yel-
low.
3. Press the T1 button, the headset searches for the center
module. You can hear "Connecting center module A"
and the lane Indicator will blink yellow.
and the lane Indicator will blink yellow.
* Press the T2 button (at double-drive-thru), for other cen-
ter modules. You can hear "Connecting center module
B" and the lane indicator will blink green.
B" and the lane indicator will blink green.
When the ID Registration succeeds, you will hear
"Registration complete" and the headset number, and
the power indicator stops blinking and stays on.
"Registration complete" and the headset number, and
the power indicator stops blinking and stays on.
4. When IDs are registered on all headsets, press the ID
Registration button of the center module, ID registration
mode is completed. The power indicator of the headset
will change from yellow to green.
mode is completed. The power indicator of the headset
will change from yellow to green.
Notes:
• If ID registration fails, a warning sounds "beep" and then
you will hear a voice prompt say "Failed". If registration
fails, the ID is not registered and the "Power" indicator
blinks red.
If this happens, turn off the power and try registering
again.
fails, the ID is not registered and the "Power" indicator
blinks red.
If this happens, turn off the power and try registering
again.
• All-in-One Headset or Order Taker that can register in
one center module is up to 32.
If you register IDs exceeding 32, the unused ID that has
been registered is automatically deleted in chronological
order.
If you register IDs exceeding 32, the unused ID that has
been registered is automatically deleted in chronological
order.
• If ID registration is performed for 2 or more headsets,
follow the steps 2-4 individually.
■ Deletion of ID
To delete the registered ID of All-in-One Headset, follow the
steps below.
steps below.
1. Hold down the POWER button for more than 2 seconds
to turn off the power of All-in-On-Headset.
2. To delete an ID that is registered for LANE A, keep
pressing the T1 and C buttons simultaneously and start
up the power of All-in-One Headset.
To delete an ID that is registered for LANE B, keep
pressing the T2 and C buttons simultaneously and start
up the power of All-in-One Headset. The power indicator
then blinks in yellow.
up the power of All-in-One Headset.
To delete an ID that is registered for LANE B, keep
pressing the T2 and C buttons simultaneously and start
up the power of All-in-One Headset. The power indicator
then blinks in yellow.
3. Press the P button while the power indicator keeps blink-
ing in yellow. The ID that is registered for LANE A (or
LANE B) is deleted.
LANE B) is deleted.
4. The power indicator turns to blinking in red. A message
of "ID is not registered" is heard from the All-in-One
Headset speaker.
Headset speaker.
Power button
Keep holding
down (LANE A)
down (LANE A)
Keep holding
down (LANE B)
down (LANE B)
Keep holding
down
down
Keep holding
down
down