Korg D3200 User Manual
154
: Type
The left/right panning of the delay can be modified by chang-
ing the connections of the left and right delay. Be aware that dif-
ferent sounds must be input to the left and right channels in
order for this parameter to be effective.
ing the connections of the left and right delay. Be aware that dif-
ferent sounds must be input to the left and right channels in
order for this parameter to be effective.
This stereo delay uses an LFO to sweep the delay time. The
pitch also varies. You will obtain a delay sound with swell
and shimmering. You can also control the delay time using a
modulation source.
pitch also varies. You will obtain a delay sound with swell
and shimmering. You can also control the delay time using a
modulation source.
: L LFO Phase [degree], : R LFO Phase [degree]
“L LFO Phase”
and “R LFO Phase” specify the phase differ-
ence between the two LFO’s when they are reset. This allows
the pitch change of the sweep to be set independently for left
and right.
the pitch change of the sweep to be set independently for left
and right.
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you input signals at a
high velocity or only when the volume level is low.
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you input signals at a
high velocity or only when the volume level is low.
: Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
(effect balance), or feedback amount control.
: Polarity, : Threshold, : Offset, : Attack, : Release
The “Offset” parameter specifies the value for the “Control
Target”
Target”
parameter (when level control is not being applied),
expressed as a ratio relative to the parameter setting.
If “Polarity” is set to [+] Plus, “Control Target” will be the
value of the parameter multiplied by the “Offset” when the
input signal is lower than the “Threshold,” or will be the value
of the parameter when the input signal is above the “Thresh-
old.”
If “Polarity” is set to [–] Minus, “Control Target” will be the
value of the parameter when the input signal is lower than the
“Threshold,”
If “Polarity” is set to [+] Plus, “Control Target” will be the
value of the parameter multiplied by the “Offset” when the
input signal is lower than the “Threshold,” or will be the value
of the parameter when the input signal is above the “Thresh-
old.”
If “Polarity” is set to [–] Minus, “Control Target” will be the
value of the parameter when the input signal is lower than the
“Threshold,”
or will be the value of the parameter multiplied
by the “Offset” when the input signal is above the “Thresh-
old.”
The “Attack” and “Release” parameters specify attack time
and release time of delay level control.
old.”
The “Attack” and “Release” parameters specify attack time
and release time of delay level control.
This stereo delay effect pans the delay sound left and right
using the LFO.
using the LFO.
LoDamp (Low Damp)
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)
53Hz...20.0kHz, THRU
Sets the damping amount in the high range
In Level (Input Level)
0...100%
Sets the input level to the effect
11: St.Modulation Dly
(Stereo Modulation Delay)
L Time (L Delay Time)
0...2.500sec
Sets the left delay time
R Time (R Delay Time)
0...2.500sec
Sets the right delay time
*LFO Speed
0.02...20.00Hz
Sets the LFO speed
Dry:Wet
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
*L Depth
0...200
Sets the depth of the left LFO modulation
*R Depth
0...200
Sets the depth of the right LFO modulation
LFO Wave (LFO Waveform)
Triangle, Sine
Selects LFO Waveform
LFO Shape
–100...+100%
Determines how much the LFO waveform is changed
L Fdback (L Feedback)
–100...+100%
Sets the feedback amount of left delay
R Fdback (R Feedback)
–100...+100%
Sets the feedback amount of right delay
L Phase (L LFO Phase)
–180...+180deg
Sets the phase obtained when the left LFO is reset
R Phase (R LFO Phase)
–180...+180deg
Sets the phase obtained when the right LFO is reset
12: St.Dynamic Delay
(Stereo Dynamic Delay)
L Time (L Delay Time)
0...2.730sec
Sets the left delay time
R Time (R Delay Time)
0...2.730sec
Sets the right delay time
Feedback
–100...+100%
Sets the feedback amount
Dry:Wet
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Threshold
0...100
Adjusts the level at which compression
Attack
0...1.00sec
Sets the attack time of level control
Release
0...10.0sec
Sets the release time of level control
Offset
0...100%
Sets the offset of level control
Control (Control Target)
None, WetLevel, Feedback
Selects from no control, output, and feedback
LoDamp (Low Damp)
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)
53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Spread
0...100%
Sets the width of the stereo image of the effect sound
Polarity
[+]Plus, [–]Minus
Reverses level control
13: Auto Panning Delay
L Time (L Delay Time)
0...2.730sec
Sets the left delay time
R Time (R Delay Time)
0...2.730sec
Sets the right delay time
*Speed (Panning Speed)
0.02...20.00Hz
Sets the panning speed
Dry:Wet
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
L Fdback (L Feedback)
–100...+100%
Sets the feedback amount for the left channel
R Fdback (R Feedback)
–100...+100%
Sets the feedback amount for the right channel
*Depth (Panning Depth)
0...100
Sets the panning width
L-R Phase (LFO L-R Phase)
–180...+180deg
Sets the LFO phase difference between the left and right
LoDamp (Low Damp)
THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)
53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Waveform (LFO Waveform)
Triangle, Sine
Selects LFO Waveform
LFO Shape
–100...+100%
Determines how much the LFO waveform is changed