Konexx MOBILE KONNECTOR User Manual
♦
Converts the 4-wire handset jack to a 2-wire RJ-11 jack.
♦
Transforms the handset impedance to telephone line impedance, and vice versa.
♦
Transforms the handset signal levels to modem signal levels, and vice versa.
♦
Uses the Level switch to match the modem signal to the telephone being used. This four-position switch handles most
telephones
telephones
.
♦
Operates at data rates up to 33.6 Kbps (kilobits per second).
♦
Works with virtually all telephones that have a modular handset. The handset must be out of the cradle.
FCC Requirements
Part 68
This device has been granted a registration number by the Federal Communications Commission (FCC), under Part 68 rules and regulations for direct connection to the telephone
lines. In order to comply with these FCC rules, the following instructions must be carefully read and applicable portions followed completely. These instructions must be supplied to the
consumer.
lines. In order to comply with these FCC rules, the following instructions must be carefully read and applicable portions followed completely. These instructions must be supplied to the
consumer.
1.
This equipment complies with Part 68 of the FCC rules. A label located on the outside surface of this equipment contains, among other information, the FCC registration number
and ringer equivalence number (REN). If requested, this information must be provided to the telephone company.
and ringer equivalence number (REN). If requested, this information must be provided to the telephone company.
2.
As indicated below the suitable jack (USOC connecting arrangement) for this equipment is shown. If applicable, the facility interface codes (FIC) and service order codes (SOC)
are shown.
are shown.
3.
The ringer equivalence number (REN) is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may
result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of
devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
4.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance. But if advance notice is not practical, the telephone company will notify
the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
5.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone
company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.
company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.
6.
If trouble is experienced with this equipment, please contact the service center for repair and/or warranty information. If the trouble is causing harm to the telephone network, the
telephone company may request you to remove the equipment from the network until the problem is resolved. User repairs must not be made, and doing so will void the warranty.
telephone company may request you to remove the equipment from the network until the problem is resolved. User repairs must not be made, and doing so will void the warranty.
7.
This equipment cannot be used on coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact your state public utilities
commission for information.) If so required, this device is hearing-aid compatible (EAC).
commission for information.) If so required, this device is hearing-aid compatible (EAC).
Industry Canada (IC) Requirements
LOAD NUMBER: 0.00
NOTICE: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecommunications
network protective operational and safety requirements. The Department does not quarantee the equipment will operate to the user's satisfaction.
network protective operational and safety requirements. The Department does not quarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line
individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance
with the above conditions may not prevent degradation of service in some situations.
equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line
individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance
with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by
the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
User's should ensure for their own protection that electrical ground connections of the power utility, telephone lines and internal metalic water pipe system, if
present, are connected together. This precaution may be particularly important in rural areas.
present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Do NOT attempt to make such connections yourself; contact the appropriate electrical inspection authority or electrician.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to the telephone loop used by the device,
without overloading. The termination on a loop may consist of any combination of devices, subject only to the requirement that the total of the Load Numbers
of all the devices not exceed 100.
without overloading. The termination on a loop may consist of any combination of devices, subject only to the requirement that the total of the Load Numbers
of all the devices not exceed 100.