JVC KA-MR100G User Manual
14
Others
When warning messages appear on the LCD panel, take the
following actions.
following actions.
Battery and Signal Error Messages
An error message appears at the first line of the LCD panel
display when the battery is weak or when there is an input
signal error. When an error message appears, take the
following actions.
display when the battery is weak or when there is an input
signal error. When an error message appears, take the
following actions.
(*1) Appears during the recording or stop mode.
Card Error Messages
When an SxS memory card incompatible with the memory
recorder is detected, an
recorder is detected, an
AERROR CARD!B message and a
message indicating the cause of the card error will appear
alternately at the first line of the LCD panel display. (For
approximately two seconds) When an error message
appears, take the following actions.
alternately at the first line of the LCD panel display. (For
approximately two seconds) When an error message
appears, take the following actions.
Card error message appears when the following operations
are performed.
are performed.
● When an SxS memory card is inserted
● When power is turned on with an SxS memory card
inserted
䡵 When in the stop, standby or still mode
Status screen (stop or standby)
Status screen (stop or standby)
Clip selection screen (still)
䡵 When in the menu screen display
Warning Messages
Message
Description
CLOCK
SETUP
MENU
SETUP
MENU
Appears when the clock is not set.
Action: Set the clock when the [CLOCK1]
setting screen appears.
Action: Set the clock when the [CLOCK1]
setting screen appears.
WRITE
PROTECT!
PROTECT!
Appears when the write-protect switch of
the SxS memory card is set to the “WP”
end.
Action: Set the write-protect switch to
the SxS memory card is set to the “WP”
end.
Action: Set the write-protect switch to
AOffB
before recording or deleting a clip.
CARD FULL!
Appears when there is no more space left
on the SxS memory card.
Action: Take any of the following actions.
on the SxS memory card.
Action: Take any of the following actions.
● Use an SxS memory card with sufficient
space.
● Delete unwanted clips or format the card
to create space.
OPERATION
LOCK !
LOCK !
Appears when buttons other than the
[MENU] button is pressed with the
[OPERATION] menu set to
[MENU] button is pressed with the
[OPERATION] menu set to
ALOCKB.
Action: Change the [OPERATION] menu
setting to
setting to
AUNLOCKB.
Error Messages
Message
Description
BAT.
ALARM !
ALARM !
Appears when the remaining battery level
is insufficient.
Action: Charge the battery.
is insufficient.
Action: Charge the battery.
SHUT
DOWN !
DOWN !
Appears immediately before the battery
runs out completely. The memory recorder
will shut down a few seconds after the
message is displayed.
Action: Charge the battery.
runs out completely. The memory recorder
will shut down a few seconds after the
message is displayed.
Action: Charge the battery.
NO SIGNAL !
(*1)
(*1)
Appears when there is no signal input.
Action: Check the connection of the
IEEE1394 cable and the camcorder
settings.
Action: Check the connection of the
IEEE1394 cable and the camcorder
settings.
Other
SIGNAL (*1)
SIGNAL (*1)
Appears when the format of input signals is
different from that of the memory recorder.
Action: Make sure that the memory
recorder settings are consistent with those
of the camcorder. (
different from that of the memory recorder.
Action: Make sure that the memory
recorder settings are consistent with those
of the camcorder. (
Warning Messages
WRITE
PROTECT!
Message
Description
NO
SUPPORT!
SUPPORT!
Appears when a media not supported by
the memory recorder is inserted.
Action: Replace it with a recommended
SxS memory card.
the memory recorder is inserted.
Action: Replace it with a recommended
SxS memory card.
FORMAT!
Appears when the card has already been
formatted by another device.
Action: Execute
formatted by another device.
Action: Execute
AFORMATB using this
CARD
CHANGE
CHANGE
Appears when errors are found in the clip.
Action: Execute
Action: Execute
ARESTOREB or
AFORMATB using this memory recorder. If
doing so does not eliminate the error, it
may be due to malfunction of the SxS
memory card. Replace the SxS memory
card.
may be due to malfunction of the SxS
memory card. Replace the SxS memory
card.
RESTORE !
Appears when the clip may be damaged.
Action: Execute
Action: Execute
ARESTOREB using this
memory recorder.
<LCD Panel>
<LCD Panel>
<LCD Panel>
KA-MR100G_EN.book Page 14 Thursday, February 5, 2009 5:28 PM