Jenn-Air 30" (76.2 CM) AND 36" (91.4 CM) GAS DOWNDRAFT COOKTOP W10574732A User Manual

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.

■

Metal ducting

■

Vent clamps

■

Jenn-Air wall cap

Jenn-Air

®

 6" (15.2 cm) Round Surface Wall Cap Damper

Order Part Number A406

Jenn-Air

®

 3¼" x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper

Order Part Number A403

To order, see the “Assistance or Service” section of the Use 
and Care Guide.

Check local codes and consult gas supplier. Check existing gas 
supply and electrical supply. See “Electrical Requirements” and 
“Gas Supply Requirements” sections.

It is recommended that all electrical connections be made by a 
licensed, qualified electrical installer.

IMPORTANT: Observe all governing codes and ordinances. 
When installing cooktop, use minimum dimensions given.

■

It is the installer’s responsibility to comply with installation 
clearances specified on the model/serial rating plate. The 
model/serial rating plate is located on side of the downdraft 
plenum.

■

To eliminate the risk of burns or fire by reaching over the 
heated surface units, cabinet storage space located above 
the surface units should be avoided. If cabinet storage is to 
be provided, the risk can be reduced by installing a range 
hood that projects horizontally a minimum of 5" (12.7 cm) 
beyond the bottom of the cabinets.

■

The cooktop should be installed in a location away from 
strong draft areas, such as windows, doors and strong 
heating vents or fans.

■

All openings in the wall or floor where cooktop is to be 
installed must be sealed.

■

Cabinet opening dimensions that are shown must be used. 
Given dimensions are minimum clearances.

■

Grounded electrical supply is required. See “Electrical 
Requirements” section. Proper gas supply connection must 
be available. See “Gas Supply Requirements” section.

■

The cooktop is designed to hang from the countertop by its 
side or rear flanges.

■

The gas and electric supply should be located as shown in 
“Cabinet Dimensions” section so that they are accessible 
without requiring removal of the cooktop.

■

Provide cutout in right rear corner of cabinet enclosure as 
shown to provide clearance for gas inlet, power supply cord, 
and to allow the rating label to be visible.

■

If cabinet has drawers, drawers will need to be removed and 
drawer fronts installed on front of cabinet.

IMPORTANT: An undercounter built-in oven cannot be installed 
under this product.

IMPORTANT: To avoid damage to your cabinets, check with your 
builder or cabinet supplier to make sure that the materials used 
will not discolor, delaminate or sustain other damage. This 
cooktop has been designed in accordance with the requirements 
of UL and CSA International and complies with the maximum 
allowable wood cabinet temperatures of 194°F (90°C).

The installation of this cooktop must conform to the 
Manufactured Home Construction and Safety Standard, Title 24 
CFR, Part 3280 (formerly the Federal Standard for Mobile Home 
Construction and Safety, Title 24, HUD Part 280). When such 
standard is not applicable, use the Standard for Manufactured 
Home Installations, ANSI A225.1/NFPA 501A or local codes.

■

In Canada, the installation of this cooktop must conform with 
the current standards CAN/CSA-A240-latest edition, or with 
local codes.

■

Tape measure

■

Flat-blade screwdriver

■

Phillips head screwdriver

■

Drill

■

Level

■

6" (15.2 cm) socket 
extension

■

Marker or pencil

■

Pliers

■

¼" drill bit

■

Jigsaw

■

Ratchet with 

³⁄₈" socket

■

Pipe-joint compound 
resistant to LP gas

■

Noncorrosive leak-detection 
solution

■

Vent grill

■

Pre-filter

■

LP conversion kit

■

Burner caps

■

Burner grates

■

Pressure regulator

¹¹⁄₁₆

C

A

B