Multiquip Boat MT55F User Manual
PAGE 24 — MT55F RAMMER — OPERATION AND PARTS MANUAL — REV. #5 (01/06/12)
NAMEPLATE AND DECALS
Mikasa
4
Mikasa
MT-55F
3
7
11
OHV
5
12
6
2
1
Oil
öl
I’ huile
SAE30
7~9 cc
SAE30
7~9 cc
NPA-961 E
GASOLINE ONLY
GASOLINE ONLY
DCL205
PRIMARY AIRFILTER
CHECK DAILY
DCL207
READ OWNER’S SERVICE MANUAL BEFORE OPERATING OR
SERVICING THIS MACHINE.
SERVICING THIS MACHINE.
ALWAYS KEEP UNAUTHORIZED, INEXPERIENCED,
UNTRAINED PEOPLE AWAY FROM THIS MACHINE.
UNTRAINED PEOPLE AWAY FROM THIS MACHINE.
MAKE SURE ALL SAFETY DEVICES ARE OPERATIONAL
BEFORE THIS MACHINE IS STARTED. MAKE SURE ENGINE
IS TURNED OFF AND SPARK PLUG WIRE DISCONNECTED
BEFORE SERVICING THE MACHINE OR COMING IN
CONTACT WITH ANY MOVING PART. IF EQUIPMENT IS
POWERED BY AN ELECTRIC MOTOR DISCONNECT
ELECTRICAL PLUG.
BEFORE THIS MACHINE IS STARTED. MAKE SURE ENGINE
IS TURNED OFF AND SPARK PLUG WIRE DISCONNECTED
BEFORE SERVICING THE MACHINE OR COMING IN
CONTACT WITH ANY MOVING PART. IF EQUIPMENT IS
POWERED BY AN ELECTRIC MOTOR DISCONNECT
ELECTRICAL PLUG.
NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING.
ALWAYS STOP ENGINE AND ALLOW ENGINE TO COOL
BEFORE ADDING FUEL OR OIL.
ALWAYS STOP ENGINE AND ALLOW ENGINE TO COOL
BEFORE ADDING FUEL OR OIL.
NPA-329 J
CLEANING ELEMENT:
Remove the element from the pre-cleaner
Clean the element with solvent
Apply SAE30 motor oil with 7~9 cc, and
squeeze out excess oil before re-installing.
Remove the element from the pre-cleaner
Clean the element with solvent
Apply SAE30 motor oil with 7~9 cc, and
squeeze out excess oil before re-installing.
NPA-963 J
Prior to each operation check
Check all nuts and bolts for tightness.
Check oil levels in both the engine and the lower unit.
Keep machine at the upright operating position to check.
1. Lower unit assembly-Check sight glass for proper level.
2. Engine-Fill to the lower outer rim.
Check oil levels in both the engine and the lower unit.
Keep machine at the upright operating position to check.
1. Lower unit assembly-Check sight glass for proper level.
2. Engine-Fill to the lower outer rim.
To START engine:
Open fuel filter valve and close choke lever on carburetor.
Place starter switch to “ON” and pull start rope.
When engine starts, open the choke lever and warm up the
engine for 4-5 minutes before operation.
Open fuel filter valve and close choke lever on carburetor.
Place starter switch to “ON” and pull start rope.
When engine starts, open the choke lever and warm up the
engine for 4-5 minutes before operation.
To STOP engine:
Move the throttle lever quickly from “ON” to “OFF” position.
Then move starter switch to “OFF” and close the fuel filtervalve.
Then move starter switch to “OFF” and close the fuel filtervalve.
CAUTION
OPERATION
NPA-975 J
When you stop
the engine, be
sure to close
the fuel cock
the engine, be
sure to close
the fuel cock
NPA-399 J
NAMEPLATE
NP-831 J
CLEAN THE ELEMENT WITH KEROSENE WHEN DIRTY. AFTER THE
CLEANING, LUBRICATE IT MIXED OIL (KEROSENE 2~4: ENGINE OIL
1), SQUEEZE OUT THE OIL, AND REPLACE IT. AND CLEAN IT MORE
OFTEN WHEN OPERATING IN DUSTY CONDITIONS.
CLEANING, LUBRICATE IT MIXED OIL (KEROSENE 2~4: ENGINE OIL
1), SQUEEZE OUT THE OIL, AND REPLACE IT. AND CLEAN IT MORE
OFTEN WHEN OPERATING IN DUSTY CONDITIONS.
NOTICE
14
3800 ~ 4100 RPM
NPA-957 J
13
To start, switch must be
in the “
in the “
” position
ON
NPA 293
9
* Read operator’s manual carefully before use.
* Libre le manual attentivement avant utillsation.
* Bitte lesen Sie vor inbetriebnahme der Maschine de
* Libre le manual attentivement avant utillsation.
* Bitte lesen Sie vor inbetriebnahme der Maschine de
Bedienungsanleitung sogfältig durch.
* Prima dell’ uso leggere attentamente il manuale.
* Lee com atenÇão o manual de instruÇões antes de
* Lee com atenÇão o manual de instruÇões antes de
usar.
* Leer detenidamente el mamual de instrucciones
antes de usar la maquina.
CAUTION
ATTENZIONE
ATENÇAÕ
PRECAUCION
NPA-769 J
10
NP
A-910
J
8