Motion Computing FWS-DS1 User Manual
1
English
English
This document contains regulatory, precautionary, and
recycling information for the Motion CL-Series Docking
Station Model FWS-DS1. To avoid injury, read this
document and understand its contents before you use the
docking station. Keep this document nearby, so you can
refer to it later.
recycling information for the Motion CL-Series Docking
Station Model FWS-DS1. To avoid injury, read this
document and understand its contents before you use the
docking station. Keep this document nearby, so you can
refer to it later.
For detailed operating instructions and safety information,
see
see
The Motion Docking Station Model FWS-DS1is marketed
and/or known as the CL-Series Docking Station.
and/or known as the CL-Series Docking Station.
Note: The Motion Docking Station Model FWS-DS1 is
compliant to the IEC/EN 60950-1:2006+A11:2009 Safety
Standard for Information Technology Equipment.
compliant to the IEC/EN 60950-1:2006+A11:2009 Safety
Standard for Information Technology Equipment.
Specifications
Product safety information
Motion Docking Stations are designed to optimize safety
and minimize strain. However, to further reduce the risk of
injury or damage to the unit, you should observe certain
precautions.
and minimize strain. However, to further reduce the risk of
injury or damage to the unit, you should observe certain
precautions.
Mounting and installation disclaimer
Motion Computing shall not be liable under any theory of
liability (including, without limitation, contract, tort or
statutory law) for any loss, damage, personal injury, or
other damage of any nature (including, without limitation,
direct, special, incidental or consequential damages)
arising directly or indirectly as a result of improper or
inappropriate placement, installation, or use of its products
or any other application. To safely install and use Motion
products, full consideration of occupants, systems (e.g., the
location of fuel lines, navigation systems, brakes lines,
electrical, drive train or other systems), air-bags and other
back-up, warning or safety equipment is required. Without
limiting the foregoing, Motion specifically disclaims any
responsibility for the placement, use, or installation of its
products not consistent with (i) the original manufacturer’s
or governmental or regulatory specifications and
recommendations for the environment where the products
will be placed, used, or installed, (ii) Motion written product
instruction sheets, or (iii) workmanship standards.
liability (including, without limitation, contract, tort or
statutory law) for any loss, damage, personal injury, or
other damage of any nature (including, without limitation,
direct, special, incidental or consequential damages)
arising directly or indirectly as a result of improper or
inappropriate placement, installation, or use of its products
or any other application. To safely install and use Motion
products, full consideration of occupants, systems (e.g., the
location of fuel lines, navigation systems, brakes lines,
electrical, drive train or other systems), air-bags and other
back-up, warning or safety equipment is required. Without
limiting the foregoing, Motion specifically disclaims any
responsibility for the placement, use, or installation of its
products not consistent with (i) the original manufacturer’s
or governmental or regulatory specifications and
recommendations for the environment where the products
will be placed, used, or installed, (ii) Motion written product
instruction sheets, or (iii) workmanship standards.
Setup precautions
•
Read the installation instructions before connecting the
docking station to the power supply.
docking station to the power supply.
•
Place the docking station on a level surface so that it
does not fall over and damage the unit, the docking
station, or other components.
does not fall over and damage the unit, the docking
station, or other components.
•
Do not use the docking station adapter for other
equipment. This can generate heat or fire. In addition,
do not use other AC adapters with the docking station.
equipment. This can generate heat or fire. In addition,
do not use other AC adapters with the docking station.
Basic personal safety precautions
•
Do not attempt to service the docking station nor its
components yourself. Perform only those service
procedures for which Motion provides special
instructions, for example, installing a peripheral device.
components yourself. Perform only those service
procedures for which Motion provides special
instructions, for example, installing a peripheral device.
•
Do not connect or disconnect any cables or perform
maintenance or reconfiguration of this product during
an electrical storm.
maintenance or reconfiguration of this product during
an electrical storm.
Docking station disposal
•
Do not dispose of the CL-Series Docking Station with
general waste.
general waste.
•
If you cannot locate a disposal site, contact your reseller
or Motion Computing for assistance in locating a
disposal site near your locale.
or Motion Computing for assistance in locating a
disposal site near your locale.
Cabling and power cord precautions
•
Power cord sets for use in other countries must meet
the requirements of that country. Use the appropriate
AC adapter and power cord for your locale. For
information about power cord set requirements,
contact the Motion Reseller from whom you purchased
the product, or contact Motion Computing if you
purchased the product from Motion Computing.
the requirements of that country. Use the appropriate
AC adapter and power cord for your locale. For
information about power cord set requirements,
contact the Motion Reseller from whom you purchased
the product, or contact Motion Computing if you
purchased the product from Motion Computing.
•
If no power cord was provided for your docking station
or an accessory, purchase a power cord that is approved
for use in your country and that matches the required
voltage and amperage rating.
or an accessory, purchase a power cord that is approved
for use in your country and that matches the required
voltage and amperage rating.
•
If you use an extension cord with your AC adapter,
ensure that the total ampere rating of the products
plugged into the extension cord does not exceed the
ampere rating of the extension cord.
ensure that the total ampere rating of the products
plugged into the extension cord does not exceed the
ampere rating of the extension cord.
•
When using your power cord, make sure to position it
around objects so it will not be cut or punctured.
around objects so it will not be cut or punctured.
Component replacement precautions
•
Components currently available from Motion
Computing as replaceable parts include the AC power
adapter (rated for general use). Components may
change from time to time. Contact Motion Computing
for more information or if you have any questions about
replacing a specific component.
Computing as replaceable parts include the AC power
adapter (rated for general use). Components may
change from time to time. Contact Motion Computing
for more information or if you have any questions about
replacing a specific component.
Environmental statements
•
This product is in compliance with Directive 2002/95/EC
of the European Parliament and of the Council set into
force in January 2003. This Directive set into force
procedures regarding the restriction of the use of
certain substances in electric and electrical equipment
(ROHS).
of the European Parliament and of the Council set into
force in January 2003. This Directive set into force
procedures regarding the restriction of the use of
certain substances in electric and electrical equipment
(ROHS).
•
This product is in compliance with Directive 2002/96/EC
of the European Parliament and of the Council set into
force in January 2003. This Directive set into force
procedures regarding the Waste of Electrical and
of the European Parliament and of the Council set into
force in January 2003. This Directive set into force
procedures regarding the Waste of Electrical and
On
Off (Storage)
Temperature
5–45° C
0–45° C (with
SSD option)
0–45° C (with
SSD option)
-20–60° C
Humidity
8–90% RH
5–95% RH
Air pressure
697–1060 hPa
187–1060 hPa
Power supply
(ITE) Delta
Electronics,
SADP-65NB
Rev. BB
(ITE) Delta
Electronics,
SADP-65NB
Rev. BB
Input: 1.5 A, 100–240 VAC, 47–63 Hz
Output: 19 V DC, 3.42 A
The power supply is compliant with
UL 60950-1, CAN/CSA C22.2
No. 60950-1, and IEC/EN 60950-1
Output: 19 V DC, 3.42 A
The power supply is compliant with
UL 60950-1, CAN/CSA C22.2
No. 60950-1, and IEC/EN 60950-1