Microsoft ES4612 User Manual
Configuring the Switch
3-232
3
Configuring OSPF Interfaces
You should specify a routing interface for any local subnet that needs to
communicate with other network segments located on this router or elsewhere in the
network. First configure a VLAN for each subnet that will be directly connected to
this router, assign IP interfaces to each VLAN (i.e., one primary interface and one or
more secondary interfaces), and then use the OSPF / Network Area Address
Configuration page to assign an interface address range to an OSPF area.
communicate with other network segments located on this router or elsewhere in the
network. First configure a VLAN for each subnet that will be directly connected to
this router, assign IP interfaces to each VLAN (i.e., one primary interface and one or
more secondary interfaces), and then use the OSPF / Network Area Address
Configuration page to assign an interface address range to an OSPF area.
After assigning a routing interface to an OSPF area, you need to use the OSPF /
Interface Configuration page to configure the interface-specific parameters used by
OSPF to select the designated router, control the timing of link state advertisements,
set the cost used to select preferred paths, and specify the method used to
authenticate routing messages.
Interface Configuration page to configure the interface-specific parameters used by
OSPF to select the designated router, control the timing of link state advertisements,
set the cost used to select preferred paths, and specify the method used to
authenticate routing messages.
Field Attributes
OSPF Interface List
• VLAN ID – The VLAN to which an IP interface has been assigned.
• Interface IP – The IP interface associated with the selected VLAN.
• Area ID – The area to which this interface has been assigned.
• Designated Router – Designated router for this area.
• Backup Designated Router – Designated backup router for this area.
• Entry Count – The number of IP interfaces assigned to this VLAN.
• VLAN ID – The VLAN to which an IP interface has been assigned.
• Interface IP – The IP interface associated with the selected VLAN.
• Area ID – The area to which this interface has been assigned.
• Designated Router – Designated router for this area.
• Backup Designated Router – Designated backup router for this area.
• Entry Count – The number of IP interfaces assigned to this VLAN.
Note:
This router supports up 64 OSPF interfaces.
Detail Interface Configuration
• VLAN ID – The VLAN corresponding to the selected interface.
• Rtr Priority – Sets the interface priority for this router. (Range: 0-255; Default: 1)
• VLAN ID – The VLAN corresponding to the selected interface.
• Rtr Priority – Sets the interface priority for this router. (Range: 0-255; Default: 1)
- A designated router (DR) and backup designated router (BDR) is elected for
each OSPF area based on Router Priority. The DR forms an active adjacency to
all other routers in the area to exchange routing topology information. If for any
reason the DR fails, the BDR takes over this role.
all other routers in the area to exchange routing topology information. If for any
reason the DR fails, the BDR takes over this role.
- The router with the highest priority becomes the DR and the router with the next
highest priority becomes the BDR. If two or more routers are set to the same
priority, the router with the higher ID will be elected. You can set the priority to
zero to prevent a router from being elected as a DR or BDR.
priority, the router with the higher ID will be elected. You can set the priority to
zero to prevent a router from being elected as a DR or BDR.
- If a DR already exists for an area when this interface comes up, the new router
will accept the current DR regardless of its own priority. The DR will not change
until the next time the election process is initiated.
until the next time the election process is initiated.
• Transmit Delay – Sets the estimated time to send a link-state update packet over
an interface. (Range: 1-65535 seconds; Default: 1)
- LSAs have their age incremented by a delay before transmission. You should
- LSAs have their age incremented by a delay before transmission. You should
consider both the transmission and propagation delays for an interface when
estimating this delay. Set the transmit delay according to link speed, using larger
values for lower-speed links.
estimating this delay. Set the transmit delay according to link speed, using larger
values for lower-speed links.
- The transmit delay must be the same for all routers in an autonomous system.