Lowepro RTA2072 User Manual
11
Section 2: Operating
7/03/07
RTA2064, RTA2072, RTR2064 & RTR2072 Rotary Tillers 311-328M
Land Pride
Section 2: Operating
Transporting
!
CAUTION
When traveling on public roads whether at night or during the
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
day, use accessory light and devices for adequate warning to
operators of other vehicles. Comply with all federal, state and
local laws.
1.
When raising the tiller to the transport position, be
sure that driveline does not contact tractor or tiller.
Adjust the tractor’s 3-point hitch lift height so that the
tiller tines are not lifted more than 14 inches off the
ground to prevent damage to the driveline.
sure that driveline does not contact tractor or tiller.
Adjust the tractor’s 3-point hitch lift height so that the
tiller tines are not lifted more than 14 inches off the
ground to prevent damage to the driveline.
2.
Be sure to reduce tractor ground speed when
turning; and, leave enough clearance so the tiller
does not contact obstacles such as buildings, trees
or fences.
turning; and, leave enough clearance so the tiller
does not contact obstacles such as buildings, trees
or fences.
3.
Select a safe ground travel speed when transporting
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
4.
When traveling over rough or hilly terrain, shift tractor
to a lower gear.
to a lower gear.
Parking
The following steps should be taken when preparing to
store the tiller or unhitch it from the tractor. Also see
Storage in the “Maintenance and Lubrication” section
starting on page 17 for additional information on long
term storage of your tiller.
store the tiller or unhitch it from the tractor. Also see
Storage in the “Maintenance and Lubrication” section
starting on page 17 for additional information on long
term storage of your tiller.
1.
Park the tiller on a level, solid area.
2.
Shut off tractor engine and engage parking brake.
3.
Set parking stand to desired height for re-hook-up
and install pin to lock in place.
and install pin to lock in place.
4.
Unhitch from tractor.
5.
See Storage in the “Maintenance and Lubrication”
section on page 17 if tiller is not going to be used for
a long period.
section on page 17 if tiller is not going to be used for
a long period.
General Notes for Field Operations
Before beginning to till the following inspection should be
performed:
performed:
1.
Check oil level in gearbox and chaincase. Refer to
Lubrication in the “Maintenance and Lubrication”
section starting on page 14.
Lubrication in the “Maintenance and Lubrication”
section starting on page 14.
2.
Check that all plugs have been replaced properly in
the gearbox and chaincase.
the gearbox and chaincase.
3.
Check drive chain tension. Refer to Drive Chain in
the “Adjustment” section on page 13.
the “Adjustment” section on page 13.
4.
Be sure all tiller tines, bolts and nuts are tight.
5.
Be certain all guards and shields are in place and
secure.
secure.
IMPORTANT: Always disengage PTO before raising
the tiller to transport position.
the tiller to transport position.
6.
Grease driveline shaft and all other grease fittings.
7.
Clear the area to be tilled of rocks, branches and
other foreign objects.
other foreign objects.
8.
Tall grass and weeds may need to be mowed before
tilling.
tilling.
9.
Operate with 540 rpm PTO tractor.
10. At first begin tilling at a slow forward speed and shift
up as ground conditions warrant.
11. Tiller should be operated with the tiller deck level to
the ground.
12. Tiller tines will cut better at a faster rotor speed than
at reduced throttle.
13. Do not engage PTO at full throttle.
14. Tilling should not be done in wet conditions as soil
will stick to tines.
15. After tilling the first 50 feet, stop and check to see that
the tiller is adjusted properly.
16. Do not make turns or attempt to back up while tiller is
in the ground. See important note below.
17. Do not engage PTO with machine in the fully raised
or lowered position.
18. Periodically check for foreign objects wrapped
around the rotor shaft and remove them after
disengaging PTO, turning off tractor, and removing
ignition key.
disengaging PTO, turning off tractor, and removing
ignition key.
Operating Check List
In addition to design and configuration of equipment,
hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in its operation, transport, maintenance
and storage of equipment. Before beginning to operate
your Rotary Tiller, the following inspection should be
performed.
hazard control and accident prevention are dependent
upon the awareness, concern, prudence and proper
training involved in its operation, transport, maintenance
and storage of equipment. Before beginning to operate
your Rotary Tiller, the following inspection should be
performed.
Operating Checklist
✔
Check
Reference
Read “Important Safety Information”
Read all of the Tractor Hook-Up and preparation
instructions.
instructions.
Read “Operating Instructions”
Lubricate the tiller as needed. Refer to Lubrica-
tion.
tion.
Check the tiller initially and periodically for loose
bolts & pins, Torque Values Chart.
bolts & pins, Torque Values Chart.
Make sure all guards and shields are in place.
Check initially and periodically for loose bolts, pins,
and chains.
and chains.
IMPORTANT: Turning or backing up with rotary
tines in the ground will damage the tiller.
tines in the ground will damage the tiller.