Lorex Technology SG19LD800 Series User Guide

Page of 102
iii
Important Safeguards
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacture process of your video 
product, safety is a major factor in the design of every instrument. However, safety is your responsibility too. 
This sheet lists important information that will help to assure your enjoyment and proper use of the video 
product and accessory equipment. Please read them carefully before operating and using your video product.
Installation
1. Read and Follow Instructions - All the safety and 
operating instructions should be read before the 
video product is operated. Follow all operating 
instructions.
2.  Retain Instructions - The safety and operating 
instructions should be retained for future reference.
3.   Heed Warnings - Comply with all warnings on the 
video product and in the operating instructions.
4. Polarization - Do not defeat the safety purpose of 
the polarized or grounding-type plug.
A polarized plug has two blades with 
one wider than the other.
A grounding type plug has two blades 
and a third grounding prong.
The wide blade or the third prong are 
provided for your safety.
If the provided plug does not fit into 
your outlet, consult an electrician for 
replacement of the obsolete outlet
5. .Power Sources - This video product should be 
operated only from the type of power source 
indicated on the marking label. If you are not sure of 
the type of power supply to your location, consult 
your video dealer or local power company. For video 
products intended to operate from battery power, or 
other sources, refer to the operating instructions.
6.  Overloading - Do not overload wall outlets of 
extension cords as this can result in the risk of fire 
or electric shock. Overloaded AC outlets, extension 
cords, frayed power cords, damaged or cracked wire 
insulation, and broken plugs are dangerous. They 
may result in a shock or fire hazard. Periodically 
examine the cord, and if its appearance indicates 
damage or deteriorated insulation, have it replaced 
by your service technician.
7. Power-Cord Protection - Power supply cords should 
be routed so that they are not likely to be walked on 
or pinched by items placed upon or against them, 
paying particular attention to cords at plugs, 
convenience receptacles, and the point where they 
exit from the video product.
8.   Ventilation - Slots and openings in the case are 
provided for ventilation to ensure reliable operation 
of the video product and to protect it from 
overheating. These openings must not be blocked 
or covered. The openings should never be blocked 
by placing the video equipment on a bed, sofa, rug, 
or other similar surface. This video product should 
never be placed near or over a radiator or heat 
register. This video product should not be placed in 
a built-in installation such as a bookcase or rack 
unless proper ventilation is provided or the video 
product manufacturer’s instructions have been 
followed.
9.  Attachments - Do not use attachments unless 
recommended by the video product manufacturer as 
they may cause a hazard.
10. Water and Moisture - Do not use this video product 
near water. For example, near a bath tub, wash bowl, 
kitchen sink or laundry tub, in a wet basement, near 
a swimming pool and the like. 
Caution: Maintain electrical safety. Powerline 
operated equipment or accessories connected to 
this unit should bear the UL listing mark of CSA 
certification mark on the accessory itself and should 
not be modified so as to defeat the safety features. 
This will help avoid any potential hazard from 
electrical shock or fire. If in doubt, contact qualified 
service personnel.
11. Accessories - Do not place this video equipment 
on an unstable cart, stand, tripod, or table. The video 
equipment may fall, causing serious 
damage to the video product. Use 
this video product only with a cart, 
stand, tripod, bracket, or table 
recommended by the 
manufacturer or sold with the video 
product. Any mounting of the product 
should follow the manufacturer’s 
instructions and use a mounting accessory 
recommended by the manufacturer.