Linear ACCESSPRO AP-1 Leaflet

Size: 10.5"W x 4.5"H x 2"D

Weight: 1.5 Lbs.

Supply Voltage: 12-24 Volts AC or DC

Operating Current: 250 Ma Maximum

Operating Temperature Range: -22° to +158° F (-30° to +70° C)

Sensitivity: -94 dBm Minimum

Bandwidth (3 db): 4 MHz Typical

Frequency: 318 MHz

Relay Contact Rating: 1 AMP @ 24 Volts AC or DC

This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty
Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct
from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers.
Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no
obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in
connection with use or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including
implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date
as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to:

Linear Corporation Service Department
2580 Pioneer Avenue, Suite C
Vista, CA 92083

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling.
However, there are some limitations which must be observed.
✶ For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15

devices. As such, they have limited transmitter power and therefore limited range.

✶ A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals

that occur on or near their operating frequencies, regardless of code settings. 

✶ Changes or modifications to the device may void FCC compliance.
✶ Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶ A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or

dealer, and these facts should be communicated to the ultimate users.

Copyright © 1995 Linear Corporation 

211037 B

ENTER THE NUMBER (1 TO 169) OF AN 
EMPTY MEMORY LOCATION

PRESS LEARN BUTTON

OCCUPIED LIGHT WILL BLINK FOR 2 
SECONDS IF MEMORY LOCATION IS 
EMPTY

ACTIVATE THE TRANSMITTER WHILE 
OCCUPIED LIGHT IS BLINKING

OCCUPIED LIGHT WILL LIGHT STEADY 
WHEN TRANSMITTER IS LEARNED

ENTER THE NUMBER (1 TO 169) OF 
THE MEMORY LOCATION TO CLEAR

PRESS DELETE BUTTON

OCCUPIED LIGHT WILL BLINK FOR 2 
SECONDS IF MEMORY LOCATION IS 
OCCUPIED

PRESS DELETE AGAIN WHILE 
OCCUPIED LIGHT IS BLINKING TO 
ERASE TRANSMITTER FROM MEMORY

OCCUPIED LIGHT WILL GO OUT WHEN 
TRANSMITTER HAS BEEN DELETED

ENTER THE NUMBER (1 TO 169) OF AN 
OCCUPIED MEMORY LOCATION

PRESS SUSPEND BUTTON

OCCUPIED LIGHT WILL LIGHT STEADY 
FOR 2 SECONDS IF MEMORY 
LOCATION IS OCCUPIED

SUSPENDED AND OCCUPIED LIGHTS 
WILL LIGHT STEADY WHEN THE 
TRANSMITTER HAS BEEN 
SUSPENDED

NOTE: TO "UNSUSPEND" THE TRANSMITTER, ENTER
SUSPENDED TRANSMITTER NUMBER AND PRESS SUSPEND.

ENTER MEMORY LOCATION NUMBER 
999 TO LEARN MGT TRANSMITTER

PRESS LEARN BUTTON

OCCUPIED LIGHT WILL BLINK FOR 2 
SECONDS IF MEMORY LOCATION IS 
EMPTY

OCCUPIED LIGHT WILL LIGHT STEADY 
WHEN TRANSMITTER IS LEARNED

ACTIVATE THE MGT TRANSMITTER 
WHILE OCCUPIED LIGHT IS BLINKING

IF RECEIVER IS BEEPING EVERY FIVE 
SECONDS, PRESS #-1 TO DISPLAY THE 
MGT SUPERVISORY CODES
(MULTIPLE CODES CAN BE DISPLAYED)

"L" INDICATES A LOW MGT 
TRANSMITTER BATTERY

"F" INDICATES AN MGT TAMPER OR 
LOOP FAULT CONDITION

"S" INDICATES THAT HOURLY STATUS 
REPORTS HAVE NOT BEEN RECEIVED 
FROM THE MGT FOR FOUR HOURS

AFTER SERVICING FAULT, PRESS 
OPEN TO SILENCE BEEPER AND 
RESET THE RECEIVER DISPLAYS

NOTE: IF SUPERVISION SOUNDER IS NOT REQUIRED, SUSPEND
MGT TRANSMITTER (#999). SUPERVISION CODES CAN STILL BE
DISPLAYED. THIS WILL ALSO DISABLE THE REQUIREMENT OF 
PRESSING A TRANSMITTER TWICE TO TRIGGER THE ACCESS RELAY
DURING A SUPERVISORY CONDITION.

ACTIVATE A LEARNED TRANSMITTER 
AND VERIFY THAT THE ACCESS 
DEVICE OPERATES

IF MGT OBSTACLE TRANSMITTER IS 
USED, RUN ACCESS DEVICE AND 
TRIGGER OBSTACLE SENSOR. VERIFY 
THAT ACCESS DEVICE REVERSES

IF AN OPEN REQUEST PUSHBUTTON 
IS INSTALLED, PRESS IT AND VERIFY 
THAT THE ACCESS DEVICE 
OPERATES

DISPLAYS THE MGT SUPERVISORY 
CODES

THESE HANDY UTILITY FUNCTIONS CAN SPEED SYSTEM
PROGRAMMING AND MAINTENANCE 

DISPLAYS THE NUMBER OF EMPTY 
MEMORY LOCATIONS

DISPLAYS THE NUMBER OF 
OCCUPIED MEMORY LOCATIONS

DISPLAYS THE FIRST AVAILABLE 
EMPTY MEMORY LOCATION

DISPLAYS THE VERSION NUMBER OF 
THE AP-1 FIRMWARE

WHEN DISPLAY IS BLANK, DISPLAYS THE NUMBER 
OF THE LAST TRANSMITTER ACTIVATED, OR 
SUBTRACTS 1 FROM THE DISPLAYED NUMBER

WHEN DISPLAY IS BLANK, PRESS # BEFORE 
PRESSING UTILITY FUNCTION NUMBER, OR ADDS 1 
TO A DISPLAYED NUMBER