Insignia NS-R5100 User Manual
15
Insignia NS-R5100 AV Digital Home Theater Receiver
www.insignia-products.com
Recalling the memorized channel levels
To recall the memorized channel levels:
1 Press the CHANNEL LEVEL button. CAL or
REF 1 is displayed for several seconds.
2 Press the select
or button to select
REF 1 or REF 2. The channel levels
memorized into the selected preset memory
are recalled.
memorized into the selected preset memory
are recalled.
Listening to radio broadcasts
Auto tuning
To auto tune a radio station:
1 Press FM/AM to select the band.
Each time this button is pressed, the band
changes as follows:
changes as follows:
•
FM ST
•
FM MONO
•
AM
When FM stereo broadcasts are poor
because of weak broadcast signals, select
the FM mono mode to reduce the noise. FM
broadcasts are then reproduced in monaural
sound.
because of weak broadcast signals, select
the FM mono mode to reduce the noise. FM
broadcasts are then reproduced in monaural
sound.
2 Press and hold the TUNING /
buttons
for
more than 0.5 seconds.
The tuner searches until a station of sufficient
strength has been found. The display shows
the tuned frequency and TUNED.
strength has been found. The display shows
the tuned frequency and TUNED.
If the station found is not the station you want
to listen to, repeat this procedure.
to listen to, repeat this procedure.
Weak stations are skipped during auto
tuning.
tuning.
Manual tuning
Manual tuning is useful when you already know
the frequency of the station you want to listen to.
the frequency of the station you want to listen to.
To manually tune a radio station:
1 Press FM/AM to select the band.
Each time this button is pressed, the band
changes as follows:
changes as follows:
•
FM ST
•
FM MONO
•
AM
When FM stereo broadcasts are poor
because of weak broadcast signals, select
the FM mono mode to reduce the noise. FM
broadcasts are then reproduced in monaural
sound.
because of weak broadcast signals, select
the FM mono mode to reduce the noise. FM
broadcasts are then reproduced in monaural
sound.
2 Press the TUNING
/
buttons repeatedly
until the right frequency has been reached.
Auto presetting
The Auto Presetting function automatically
searches for FM stations only and stores them in
the memory.
searches for FM stations only and stores them in
the memory.
To auto preset a radio station:
1 While listening to a radio station, press and
hold the MEMORY/ENTER button for more
than two seconds.
than two seconds.
The AUTO MEM flickers and the receiver
starts auto presetting.
starts auto presetting.
Manual presetting
To manually preset a radio station:
1 Tune to the station with auto or manual
tuning.
2 Press the MEMORY/ENTER button. MEM
flickers for several seconds.
3 Select a preset number between 1 and 30,
then press the MEMORY/ENTER button
again.
again.
4 Repeat this procedure to memorize
additional stations.
Tuning to preset stations
To tune to a preset station:
1 Select the tuner as the input source.
2 Press the PRESET
/
buttons on the
receiver.
-OR-
Enter the preset number using the numeric
keypad.
keypad.
Note
If the channel level mode display disappears,
press this button again.
press this button again.
OR
Notes
•
Up to 30 FM stations can be stored.
•
Weak FM stations cannot be stored. To store
weak stations or AM stations, perform “Manual
presetting” on page 15 along with using
“Manual tuning” on page 15.
weak stations or AM stations, perform “Manual
presetting” on page 15 along with using
“Manual tuning” on page 15.
Notes
•
When using the numeric keypad on the remote
control, press the number you want. If your
number is greater than nine, enter the first digit,
then enter the second digit within two seconds.
control, press the number you want. If your
number is greater than nine, enter the first digit,
then enter the second digit within two seconds.
•
The station has been stored in memory. When
using the numeric keypad, the station is stored
automatically without pressing the
MEMORY/ENTER button.
using the numeric keypad, the station is stored
automatically without pressing the
MEMORY/ENTER button.
•
A stored frequency is erased from memory by
storing another frequency in its place.
storing another frequency in its place.
•
If MEM goes off, start again from step 2.
Notes
When using the numeric keypad on the remote
control, press the number you want. If your
number is greater than nine, enter the first digit,
then enter the second digit within two seconds.
control, press the number you want. If your
number is greater than nine, enter the first digit,
then enter the second digit within two seconds.
TUNING