Emerson DECT 6.0 EM6113 User Manual

Remote access code - checking / setting

You need a 3-digit code (default 000) for remote access.
Press briefly to check the setting.

Press and HOLD to enter setting mode. Use and to set the first digit.
Press briefly for confirmation, and to get to the next digits input. Follow this
procedure for entering the digits and confirm by pressing . You will hear a repeat

confirmation of code.

Outgoing message - setting / checking / recording / deleting

Press and HOLD to select the OGM (outgoing message).
Press and HOLD until you hear a short beep. Speak your own new outgoing
message. Stop recording by pressing . You hear the new OGM.
Press briefly to check the OGM at any time.

It is only possible to select an outgoing message if the answering machine is turned on. If

the memory is full, only outgoing message 2 can be selected (only answering without

recording messages).

Remote access

For remote access you need a telephone using tone dialing (DTMF).

Call your number, If the answering machine is set to off it will pick up the line after 10 ring

signals. If it set to on it will pick up the line after the pre-set numbers of ring signals. You

hear an announcement and a beep. If you want to skip the announcement press the

button.

Playback messages / deleting messages

Press button. The messages will be played one after the other. If there are new
messages, only these will be played.
During playback
Press button to go to the beginning of the current message.
Press button twice to go to the previous message.
Press button to go to the next message.
Press button to pause playback (Pause), and restart playback.
Press button to stop playback (Stop).
Press button to delete the current message, press and HOLD for approxi-
mately 2 seconds until “dL” appears in the display. Press once again.
In idle state
Press button to delete all old messages (already heard), press and HOLD
for approximately 2 seconds until “dL” appears in the display. Press once again.

You’ll hear a confirmation announcement

Registering a handset

Up to five handsets can by registered to a base station. The handsets delivered with your

telephone are already registered. To register a “foreign” handset please refer to it’s user

manual.

Press the button. Select REGISTER using and press the button.
Using select a base station to subscribe to and press the button. Enter the
base’s PIN (EM6113 base station in delivery state “000”). The phone will ask “PRESS

BASE”

Press and HOLD the paging key at the base station for approximately 10 seconds.
The LED “IN USE/CHARGE” will begin to flash. After this the base station will be in
registration mode for one minute.

PAGE

MENU

MUTE

Deleting a handset

You can delete a handset from a base to allow another handset to be registered.
NOTE: You can only remove other handset in your system but you are not able to
remove the handset you are using.

Press the button. Select DE-REGISTER using and press the button.
Press and HOLD the button for approximately 3 seconds. Enter the PIN for base
station (EM6113 base station “000”). Enter the internal telephone number (1...5) of the
handset you want to remove.

Flash time

You can set the flash time to 100 ms (usually for special services of your telephone

provider/delivery state) or 600 ms (e.g. for a telephone exchange). In case of questions

please contact your telephone provider or the system administrator of your PBX.

Press the button. Select BASE using and press the button.
Using select RECALL and press the button.
Using select SHORT or LONG and press the button.

Press and HOLD the button for approximately 3 seconds. S (100ms) or L (600ms)

appears in the display.

System PIN

In delivery state the PIN is set to “000”. The PIN is valid for all registered handsets.

Press the button. Select BASE using and press the button.
Using select SYSTEM PIN and press the button. Enter the old PIN and
confirm by pressing the button. Enter the new PIN twice and confirm each by
pressing the button.

MENU

REDIAL