Emerson EM229 Owner's Manual

NOTE: This headset is capable of pairing to two mobile 

phones at the same time.

1. Make sure the headset is turned ON and connected to the 

first phone. 

2. Press and HOLD the [Volume Down] button for 3 seconds 

or until the headset’s indicator light flashes RED and BLUE 

alternately.

3. The headset is now in Pairing Mode and is ready to connect 

to your second mobile phone.

4. Set your second mobile phone to search for Bluetooth 

devices.

5. When the second phone finds the headset, confirm by 

selecting EM229 from the list.

6. Enter passcode “0000” when prompted by the second phone 

depending on which model phone you are trying to connect 

the headset to, it may not be necessary to enter a passcode. 

Select “Pair” to complete the pairing process.

7. Your mobile phone will confirm that the pairing process 

was completed. Select “Yes” to connect the headset to 

your second mobile phone. If the pairing was successful, 

the headset’s indicator light turns to standby mode and 

flashes once every three seconds.

8. After pairing the second phone, by default the first phone 

will be disconnected from the headset. Enter the first 

phone’s Bluetooth settings screen and connect it to the 

headset. Both phones should now be connected to the 

headset.

1. While on a call with one phone and the second phone rings 

with an incoming call, press and HOLD the [Volume Up] 

button briefly to answer the 2nd call and place the first 

phone on hold.

2. Press and HOLD the [Volume Up] button briefly to switch 

between the two phones and place the current phone on 

hold.

3. To hang up the current call, press the [Call] button. The 

headset will end the current call and return to the other 

phone which was placed on hold.

4. To end that call, press the [Call] button or press the [End] 

key on your phone.

NOTE: Charge the headset for at least 8 hours before using it

for the first time, even if the RED LED indicator shuts off.

Model: EM229

WIRELESS HEADSET

NOTE: To enter Pairing Mode at any time, you must press and 

HOLD the [Call] button for approximately 10 seconds.

5. Set your mobile phone to search for Bluetooth devices.

Searching for devices

Paired Devices:

1 f

ound

Stop

 *Empty *

Bluetooth: Enabled

OR depending on which model mobile phone you are trying 
to connect the headset to, it may not be necessary to enter a 
passcode and the following message (or similar) may appear on 
your phone’s display.

Enter numeric passkey

for EM229:

Paired Devices:

0000

OK

EM229

Bluetooth: Enabled

Select “Pair” to complete the pairing process.

“EM229” would like to pair

with your phone. Would you

like to allow it to pair?

Paired Devices:

Cancel

Pair

EM229

Bluetooth: Enabled

8. Your mobile phone will confirm that the pairing process was 

completed and prompt you to accept the connection. 

Please select “YES” to connect the headset to your mobile 

phone. If the pairing was successful, the headset’s indicator 

light turns to standby mode and flashes once every three 

seconds.

NOTE: The screenshots above are typical of many Bluetooth 

enabled phones in the market today, and are used to 

assist in the explanation of the pairing process. Your 

mobile phone’s or Bluetooth enabled device’s interface 

and interaction with the headset may be slightly 

different from the illustrations shown.

9. When attempting to reconnect the headset to your mobile 

phone, you may see the message below and your mobile 

phone will prompt you to accept the connection request to 

the EM229 headset, and an option not to ask this again. 

Please accept the connection, and if you select “Don’t ask this 

again”, your phone will automatically accept future connection 

requests from the headset.

Confirm connection to

EM229?

Paired Devices:

YES

NO

EM229

Bluetooth: Enabled

/

Accept connection request

from EM229?

Paired Devices:

YES

NO

EM229

Bluetooth: Enabled

/

Don’t ask this again

CAUTION: Although this device enables drivers to 
conduct handsfree conversations, it is still safer to pull
over before using a mobile phone.
Always keep your full attention on your driving.

Driving while talking on your mobile phone is dangerous, and 
illegal in many states.

Check local laws regarding the use of a mobile handset and wireless
headset while driving. If you use the Bluetooth Headset while 
driving, ensure your attention and focus remains on your driving.
 

1. Connect the charging pin of the USB cable to the charging 
    socket of the headset.
2. Connect the other end of the USB cable to either the:
 

3. The RED LED indicator light turns on while the headset is 

charging.

4. The RED LED indicator light shuts off when the headset is 

fully charged (approximately 2-3 hours).

NOTE: When the battery is running low, the RED LED indicator 
               light starts to flash along with a warning beep.

Car Charger

PC

AC Charger

Earhook

Owner’s

Manual

USB charging

cable

AC charger

Silicone cushions

S M L

Car Charger

This Bluetooth headset has an “Easy Pairing” feature which 

sets the headset to Pairing Mode the first time the power 

switch is turned on.

1. Make sure the Bluetooth Headset is within 3 feet of 

your mobile phone or Bluetooth enabled device.

2. Set the [Power] switch to the ON position. The indicator 

light should be flashing RED and BLUE alternately, 

indicating the headset is in Pairing Mode and ready to 

connect to your Bluetooth enabled device. 

3. Continue to “Manual Pairing” step 5 shown below.

Note: Manual Pairing 

If the first time pairing was unsuccessful or for 

future pairing, you will need to manually pair the 

headset to your Bluetooth enabled device (see 

“Manual Pairing” below).

Power ON/OFF

(Green = ON, Red = OFF)

(Press 3 seconds to redial)

Answer/end a call

Bluetooth

Headset

6. When the phone finds the headset, confirm by selecting 

EM229 from the list.

Select Device:

Paired Devices:

EM229

Cancel

EM229

Bluetooth: Enabled

7. Enter the passcode “0000” when prompted by the phone. 

1. Make sure the Bluetooth Headset is within 3 feet of your 

mobile phone or Bluetooth enabled device.

2. Set the [Power] switch to the ON position. 

3. Press and HOLD the [Call] button until the indicator light 

flashes RED and BLUE alternately.

4. The headset is now in Pairing Mode and is ready to connect 

to your mobile phone or Bluetooth enabled device.

within 3 feet

Power ON/OFF

(Green = ON, Red = OFF)

Power ON/OFF

(Green = ON, Red = OFF)

within 3 feet

Model: EM229

WIRELESS HEADSET