Cybex International Treadmill 710T User Manual

All of the activities listed below should be performed at the time of reaching the
mileage listed. As a aid to keep this schedule, Service Reminders will prompt
you when an activity is due. After completing the activities required, you can
clear the log by following the instructions in the Service chapter under
Diagnostic Tests, d12.

Specifications . . . . . . . . . . .  2-1

Quick Operation Guide . . . .  3-1
Detailed Operation Guide . .  3-1
Stopping the Treadmill. . . . .  3-3
Control During Operation . .  3-4
Data Readouts. . . . . . . . . . .  3-5
Selecting Programs 

& Options . . . . . . . . . . . . .  3-6

Displaying Heart Rate . . . . .  3-6
Use of Programs . . . . . . . . .  3-7
Manual Mode . . . . . . . . . . .  3-8
P1 - Fitness Test Program . .  3-8
P2 - Weight Loss Program 3-10
P3 - Cardiovascular Program 3-12
P4 - Speed Challenge 

Program . . . . . . . . . . . . .  3-14

P5 - Express Program . . . .  3-16
P6 - Hill Interval Program .  3-17
P7 - Speed Interval 

Program . . . . . . . . . . . . .  3-18

P8 - Pike’s Peak Program .  3-19
P9 - River Run Program . .  3-20
P10 - 5 Kilometer Program 3-21
P11 - Demonstration 

Program . . . . . . . . . . . . .  3-22

P101-P110 - Saved 

Program . . . . . . . . . . . . .  3-22

Workout Tips . . . . . . . . . . .  3-24

Regular Maintenance 

Activities . . . . . . . . . . . . . .  4-1

Cleaning Your Treadmill . . . .  4-1
Running Belt Maintenance .  4-2
Other Preventive 

Maintenance . . . . . . . . . . . 4-6

Service Schedule . . . . . . . . . 4-7
Log Sheet . . . . . . . . . . . . . . . 4-8

Quick Setup  . . . . . . . . . . . .  5-1
Choosing & Preparing a Site 5-1
Electrical Power 

Requirements . . . . . . . . . .  5-3

Unpacking . . . . . . . . . . . . . .  5-3
Assembling the Treadmill. . .  5-4
Testing the 710T Operation .  5-9
Setting Operation Options.  5-10

Contacting Service . . . . . . .  6-1
Serial Number & Voltage . . .  6-1
Warranty . . . . . . . . . . . . . . .  6-1
Return Material Authorization  . . 

(RMA) . . . . . . . . . . . . . . . .  6-4

Damaged Parts . . . . . . . . . .  6-4
Ordering Parts . . . . . . . . . . .  6-5

Service Instruction . . . . . . . . 7-1
Motor Brushes. . . . . . . . . . .  7-1
Motor Current & Voltage . . .  7-4
Running Belt & Deck . . . . . .  7-7
Drive Belt . . . . . . . . . . . . . . .  7-9

Odometer Reading in 

Miles (Km)

Check Running Belt & Tension/Track as needed

Vacuum debris inside hood cover and clean treadmill 

Rotate the Deck

Replace the Running Belt

Flip the Running Deck

Replace the Running Deck

Check the current draw

Measure Motor Brush Length

Measure Motor Voltage at Max Speed, No Load

500 (805)

5000 (8046)

115V Unit Current Draw: 160 lbs. user displayed current of 10.9 Amps at 0% Grade. Max current 17.9.
220V Unit Current Draw: 160 lbs. user displayed current of 9.1 Amps at 0% Grade. Max current 15.4.

Minimum brush length, as measured from top of 'box' shape to the bottom: 0.438 (7/16") (1.1 cm)

Running belt should not noticeably slip when loaded at 3.0 MPH. If so, tighten each rear bolt 1/4 turn

 

clockwise and retest.

Motor voltage at 10.0 MPH no-load should not go below:

115V Unit:  83 Volts 
220V Unit:  168 Volts

    10000 (16093)

10500 (16898)

    15000 (24140)
    20000 (32187)

20500 (32992)

    25000 (40234)
    30000 (48280)

30500 (49085)

    35000 (56327)
    40000 (64374)

40500 (67178)

    45000 (72420)

  50000 (80467)

50500 (81272)

  55000 (88514)
  60000 (96560)

60500 (97365)

  65000 (104607)
  70000 (112654)

70500 (113459)

  75000 (120701)
  80000 (128748)

80500 (129552)
85000 (136794)
90000 (144841)

m1:
m2:

 

m3:
m4:

 

m5:
m6:

 

m7:
m8:

 

m9:

m10:

 

m11:
m12:

 

m13:
m14:

 

m15:
m16:

 

m17:
m18: