Funai TB100MW9 Owner's Manual

EN

1A23

13.  Outdoor  Antenna  grounding-If an outside antenna or 

cable system is connected to this product, be sure the 
antenna or cable system is grounded so as to provide 
some protection against voltage surges and built-up static 
charges. Article 810 of the National Electrical Code, ANSI/
NFPA No. 70, provides information with respect to proper 
grounding of the mast and supporting structure, grounding 
of the lead-in wire to an antenna discharge unit, size of 
grounding conductors, location of antenna-discharge unit, 
connection to grounding electrodes, and requirements for 
the grounding electrode. (Fig. A)

14.  Lightning-For added protection for this product receiver 

during a lightning storm, or when it is left unattended and 
unused for long periods of time, unplug it from the wall 
outlet and disconnect the antenna or cable system. This 
will prevent damage to this product due to lightning and 
power-line surges.

15.  Power  Lines-An outside antenna system should not be 

located in the vicinity of overhead power lines or other 
electric light or power circuits, or where it can fall into 
such power lines or circuits. When installing an outside 
antenna system, extreme care should be taken to keep from 
touching such power lines or circuits as contact with them 
might be fatal.

16.  Overloading-Do not overload wall outlets and extension 

cords as this can result in a risk of fire or electric shock.

17.  Object  and  Liquid  Entry-Never push objects of any kind 

into this product through openings as they may touch dan-
gerous voltage points or short out parts that could result in 
a fire or electric shock. Never spill liquid of any kind on 
this product.

18.  Servicing-Do not attempt to service this product yourself 

as opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to quali-
fied service personnel.

19.  Damage  Requiring  Service-Unplug this product from the 

wall outlet and refer servicing to qualified service person-
nel under the following conditions:

a.  When the power-supply cord or plug is damaged or frayed.

b.   If liquid has been spilled, or objects have fallen into this 

product.

c.  If this product has been exposed to rain or water.

d.   If this product does not operate normally by following the 

operating instructions. Adjust only those controls that are 
covered by the operating instructions, as improper adjust-
ment of other controls may result in damage and will often 
require extensive work by a qualified technician to restore 
this product to its normal operation.

e.  If this product has been dropped or damaged in any way.

f.   When this product exhibits a distinct change in perform-

ance-this indicates a need for service.

20.  Replacement  Parts-When replacement parts are required, 

be sure the service technician has used replacement parts 
specified by the manufacturer that have the same charac-
teristics as the original part. Unauthorized substitutions 
may result in fire, electric shock, injury to persons or other 
hazards.

21.  Safety  Check-Upon completion of any service or repairs to 

this product, ask the service technician to perform routine 
safety checks to determine that this product is in proper 
operating condition.

22.  Heat-This product should be situated away from heat 

sources such as radiators, heat registers, stoves, or other 
products (including amplifiers) that produce heat.

G RO UND CL AM PS

NE C -  NA TI O NAL  EL E CTRI CAL  CO DE

W I R E

DI S CHA RG E  UN I T
(NEC  SE CTI ON 8 10 -2 0)

G RO UNDI NG  CO NDUCT ORS
(NEC  SE CTI ON 8 10 -2 1)

E L E C TR O DE   S Y S T E M
(NEC  A RT   2 50 ,   P ART  H)

S E RV I CE
E Q U I P M E N T

C L A M P

AN TE NN A
L E A D  I N

A NTEN NA

P OWE R  S E RVI C E  G RO UNDI NG

GROUN D

E L E CT RI C

X6040UD_Book.indb   3

X6040UD_Book.indb   3

10/22/2007   5:09:09 PM

10/22/2007   5:09:09 PM