Clarion CZ702 Car CD/MP3 Player CZ702 User Manual
English
7
CZ702
5. OPERATIONS
Basic Operations
Basic Operations
Note:
• Refer to the diagrams in “3. CONTROLS”
when reading this chapter.
CAUTION
When the unit is turned on, starting and
stopping the engine with its volume raised
to the maximum level may harm your
hearing.
Be careful about adjusting the volume.
stopping the engine with its volume raised
to the maximum level may harm your
hearing.
Be careful about adjusting the volume.
Power on / off
Notes:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. If you
drain the car’s battery too far, you may not
be able to start the engine and this can
reduce the service life of the battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
2. When power on first time, you can select
initial speaker system. (Refer to “Audio
Setup”)
•
INITIAL
…. When powering on the unit
for the first time, you can select a speaker
system. Check your speaker system,
choose it on the unit, and then, set your
desired sound quality referring to “Audio
Setup”.
•
LOAD
…. When powering on the unit for
the first time, “
LOAD
” is not selected.
When this unit is turned on for the first time,
it allows you to select a speaker system.
“NORMAL
” …. FRONT 2ch / REAR 2ch /
SUBWOOFER 2ch
“2WAY
” …. HIGH 2ch / MID 2ch / REAR
2ch
“3WAY
” …. HIGH 2ch / MID 2ch /
SUBWOOFER 2ch
Volume adjustment
Rotate the [
VOLUME
] knob on the front panel
or press the [ ] or [
] button on the remote
control.
The adjustable range of volume is 0 to 40.
CAUTION
While driving, keep the volume level at
which external sounds can still be heard.
which external sounds can still be heard.
Playing source selection
Press [
SRC /
] button on the front panel or
remote control repeatedly to choose desired
playing source.
Note:
Playing source selection means selecting
which mode, such as
DISC
mode,
RADIO
mode and
AUX
mode.
Display system time
Press the [
DISP
] button on the front panel or
[
DISP
] button on the remote control to switch
the display information from clock, station
information (radio mode), or track information
(CD mode).
RESET
Note:
* When the [
RESET
] button is pressed, preset
radio stations, titles, etc. stored in memory
are cleared.
RESET
To keep the current sound settings, when
power on first time after reset, rotate the
[
VOLUME]
knob to select “
LOAD
”, press the
knob to confirm.
Note:
If you press the
RESET
button or
disconnect the back-up line after
completing the audio setup, “
INITIAL
/
LOAD
” is displayed. In this case, the unit
functions as follows.
•
INITIAL
…. When powering on the
unit after
RESET
or the backup line is
disconnected, the audio setup in the
memory is cleared and you will need to
start from selecting a speaker system.
Choose your desirable speaker system
and set your desired sound quality
referring to “
Audio Setup
”.
•
LOAD
…. When powering on the unit
after
RESET
or the backup line is
disconnected, the preset speaker system
and other settings are called.
If you changed the speaker system, reset
from
INITIAL.
3. Press the [
SRC /
] button on the front
panel or the remote control to turn on
the power under standby mode. The unit
goes back to the last status after power
on.
4. Press and hold the [
SRC /
] button on
the front panel or the remote control to
turn off the power.
Mute
Press the [
MUTE
] button on the remote
control to mute the volume from the unit.
Note
:
Doing the operation above again or adjusting
volume will release muting.