Aviom AV-P2 User Manual
Connecting Audio
The audio outputs on the AV-P2 Output Module can be connected to
balanced or unbalanced devices via the Euroblock jacks.
balanced or unbalanced devices via the Euroblock jacks.
Wiring a Euroblock
Euroblock connectors provide an easy, solder-free way of making audio
connections between the AV-P2 and other audio components. Only a
small flat-blade screw driver is required to make connections. For extra
strength, you can add solder to each bare wire on an audio cable to stop
the wire strands from unwinding (called “tinning”).
connections between the AV-P2 and other audio components. Only a
small flat-blade screw driver is required to make connections. For extra
strength, you can add solder to each bare wire on an audio cable to stop
the wire strands from unwinding (called “tinning”).
LEFT
DC
POWER
RIGHT
OUT
IN
AUDIO OUTPUT
AV-P2
+ –
+ –
18-24 VDC
500mA
AV-P2 left/right Euroblock audio outputs
Connecting to a Balanced Device
To connect the AV-P2 Euroblock audio output to a device that can
accept a balanced line-level input:
accept a balanced line-level input:
Strip the insulating jacket of the cable back about .75
inch (18 mm) to reveal the individual hot, cold, and
ground wires within.
Remove a small amount of each individual wire’s
insulation (approximately .25 inch, 6 mm).
On the 5.0 mm Euroblock male plug, use a small screw
driver to loosen and open the sockets that will receive
the individual wires.
Insert the individual hot (+), cold (-), and ground wires
into the matching sockets on the Euroblock plug.
Tighten the screws on the wire sockets to secure the
individual wires.
Plug the completed Euroblock plug into the desired
output channel on the AV-P2.
Connect the AV-P2 to your audio device.
inch (18 mm) to reveal the individual hot, cold, and
ground wires within.
Remove a small amount of each individual wire’s
insulation (approximately .25 inch, 6 mm).
On the 5.0 mm Euroblock male plug, use a small screw
driver to loosen and open the sockets that will receive
the individual wires.
Insert the individual hot (+), cold (-), and ground wires
into the matching sockets on the Euroblock plug.
Tighten the screws on the wire sockets to secure the
individual wires.
Plug the completed Euroblock plug into the desired
output channel on the AV-P2.
Connect the AV-P2 to your audio device.
1.
2.
3.
4.
5.
6.
7.
The Euroblock plug, showing the screws that hold the individual wires
in place (left-to-right), hot (+), cold (-), and ground
Connecting to an Unbalanced Device
The AV-P2 audio outputs can be connected to unbalanced audio
devices; connections can use single-conductor or two-conductor
shielded cable.
devices; connections can use single-conductor or two-conductor
shielded cable.
Single-conductor shielded cable
To connect the AV-P2 audio output to an unbalanced line-level device
using single-conductor shielded cable:
using single-conductor shielded cable:
Strip the insulating jacket of the cable back about .75
inch (18 mm) to reveal the individual hot and ground
wires within.
Remove a small amount of each individual wire’s
insulation (approximately .25 inch, 6 mm).
On the Euroblock plug, use a small screw driver to
loosen and open the sockets that will receive the
individual wires.
Insert the audio cable’s hot (+) wire into the matching
socket on the Euroblock plug.
Insert the audio cable’s ground wire into the matching
socket on the Euroblock plug. The cold (-) socket on
the Euroblock remains unused in this configuration.
Tighten the screws on the wire sockets to secure the
individual wires.
Plug the completed Euroblock plug into the desired
output channel on the AV-P2.
Connect the completed cable to your audio device.
inch (18 mm) to reveal the individual hot and ground
wires within.
Remove a small amount of each individual wire’s
insulation (approximately .25 inch, 6 mm).
On the Euroblock plug, use a small screw driver to
loosen and open the sockets that will receive the
individual wires.
Insert the audio cable’s hot (+) wire into the matching
socket on the Euroblock plug.
Insert the audio cable’s ground wire into the matching
socket on the Euroblock plug. The cold (-) socket on
the Euroblock remains unused in this configuration.
Tighten the screws on the wire sockets to secure the
individual wires.
Plug the completed Euroblock plug into the desired
output channel on the AV-P2.
Connect the completed cable to your audio device.
Two-conductor shielded cable
To connect the AV-P2 audio output to an unbalanced line-level device
using two-conductor shielded cable:
using two-conductor shielded cable:
1.
2.
3.
4.
5.
6.
7.
8.