Asko W6641 W661 Manual
Page 4
Height
33-1/2”–34-1/2 (850–876 mm)
Width
23-7/16” (595 mm)
Depth
W6641/W6661: 23-7/16" (595 mm)
W6021/W6221: 24-7/16” (620 mm)
W6021/W6221: 24-7/16” (620 mm)
Weight
167 lbs. (73 kg)
Rated load
See data plate
Supply voltage
Single-phase 230 V, 60 Hz
Heating element
2000 W
Fuse
15 A (2 internal fuses)
ACCESSORIES
ACCESSORIES
INST
INSTALLA
ALLATION INSTR
TION INSTRUCTIONS
UCTIONS
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
IMPORTANT NOTE:
Cosmetic damage must be reported to your dealer
within five days from the date of purchase. After
unpacking the washer, thoroughly check the unit for
cosmetic damage.
within five days from the date of purchase. After
unpacking the washer, thoroughly check the unit for
cosmetic damage.
SPECIFICA
SPECIFICATIONS
TIONS
Drum and Barrel
Stainless steel
Outer casing
Stove-enamelled hot-dipped
galvanized steel or stainless steel
galvanized steel or stainless steel
Mounting
Four adjustable rubber-covered
feet
feet
Inlet supply hose
5 ft. (1.5 m) PEX tubing with
brass ferrules
brass ferrules
Supply pressure
15–142 PSI
Outlet hose
5.5 ft. (1.7 m) polypropylene hose,
3/4” ID
3/4” ID
Be sure to tighten the
lock nuts securely
when you level the
machine.
lock nuts securely
when you level the
machine.
REMO
REMO VING
VING THE SHIPPING
THE SHIPPING
SUPPORTS
SUPPORTS
The machine is transported with three shipping
supports, as illustrated below. These supports hold
the tub in place during shipment. When you unpack the
machine, you must remove these supports.
supports, as illustrated below. These supports hold
the tub in place during shipment. When you unpack the
machine, you must remove these supports.
To remove the shipping supports, follow the instructions
below:
below:
1. Unscrew the 5/8” (12
mm) bolts holding the
supports in place and
remove the bolts.
supports in place and
remove the bolts.
2. Push the rubber spacer
up then pull it out of the
slot.
slot.
3. Rotate the spacer so that
the extruded end points
toward the machine.
toward the machine.
4. Insert it into the slot and
push down to lock it into
position.
position.
Cold water
supply
supply
Tap
You must remove the
shipping supports
before you install the
washer.
shipping supports
before you install the
washer.
LEVELING
LEVELING THE MA
THE MACHINE
CHINE
It is important that the machine is level so it won’t vibrate
excessively during the spinning cycles. Each foot on
the washer is adjustable, so you can level the washer
on any surface. Once it is level, securely tighten the lock
nuts on the feet to prevent excessive vibration during
the spin cycles.
excessively during the spinning cycles. Each foot on
the washer is adjustable, so you can level the washer
on any surface. Once it is level, securely tighten the lock
nuts on the feet to prevent excessive vibration during
the spin cycles.
WA
WATER SUPPL
TER SUPPLY CONNECTION
Y CONNECTION
Because ASKO washers have their own heating element,
you only need to have a cold water inlet. The connection
should be made by someone who is sufficiently skilled.
Use the hose supplied with the washer.
you only need to have a cold water inlet. The connection
should be made by someone who is sufficiently skilled.
Use the hose supplied with the washer.
Water pressure must be in the range of 15–146 PSI.
A tap should be fitted on the water supply pipe.
If a new supply pipe has been installed for the washer,
it should be flushed thoroughly to remove any foreign
particles that might clog the strainer in the water inlet.
it should be flushed thoroughly to remove any foreign
particles that might clog the strainer in the water inlet.
NOTE: If unit is installed on a second story, follow
local building codes. We recommend a drip
pan be installed.
pan be installed.