Ariston Tumble dryer TVF 75C User Manual

Page of 18
19510317700 
 English, All Logos to be Ariston  
 
{PDF Created 18/01/13 22:04:00} 
11 
Start and Programmes
TD4239FUV Issue 4 
 
The Controls 
•  Programmes knob 
! Warning, 
if after pressing the start button the programme 
knob position is changed, the new position will NOT change 
the programme selected. To change programme press 
Start/Pause Button 
 to pause the programme, the light flashes 
Amber to indicate the programme is paused. Select the new 
programme and any options required, the light will then flash green. 
Press the Start/Pause Button
  and the new programme will start. 
•  Option Buttons/ Lights 
These buttons are used to customise the selected programme 
to  your requirements. A programme must  have been selected 
on the Programmes knob before an option can be selected. 
Not all options are available for all programmes (see Start and 
Programmes).
 If an option is not available and you press the 
button, the buzzer will beep three times. If the option is 
available the option light in the button lights to confirm your 
selection. 
After the start switch has been pressed were available only the 
Crease Care
 or
 Sound options (were available) can be 
changed. 
•  Progress (
 Drying, 
 Cool tumble), Icons 
These are part of the Display unit they indicate the progress of 
the dryer each one comes on as the corresponding phase 
starts. 
• 
Time Delay 
 
The start of some programmes (see Start and Programmes and 
The Display) 
can be delayed for up to 24 hours.  
 
 
Crease care  
The pre-care option is only available if a delayed start has 
been selected. It tumbles the clothes occasionally during the 
delayed period to help prevent creases developing. 
The post-care option occasionally tumbles the clothes after 
the
 
end of the drying and cool tumble cycles to help prevent 
creases developing, should you not be available to remove the 
load immediately the programme is complete. The Display 
shows 
, the Crease care and the Start/Pause Lights flash 
Amber. during this phase. Selecting this option enables both 
the pre and post care functions if appropriate and when 
selected the light in the button is on.  
Note: If you have selected the Sound option this option is not 
available. 
 
  
Sound 
If selected  gives a signal at the end of the drying cycle to 
remind you that the clothes are ready to be removed. Not 
available on Heat & Enjoy programme. 
Note: If you have selected the Crease care option this option is 
not available. 
• 
 Heat Level Button and Lights 
Not all programmes allow you to change the heat level, and 
some of these programmes do allow all three heat level 
options. When the option change the heat level is available 
pressing this button changes the heat level selected and the 
corresponding light is lit for the three available levels, Low, 
Medium and High.
 
 
DISPLAY 
 
 
The display shows either the amount of time delay remaining 
or an indication of the amount of time left for a drying 
 
programme. (see The Display
)
 The Colons between the hours 
and minutes display flash to show that the time is counting 
down. 
When the programme finishes its cool tumble phase the 
display will show 
•  Door Opening 
Opening the door (or pressing the Start/Pause Button
 ) 
during a programme will stop the dryer and have the following 
effects.. Note: The Start/Pause Light flashes Amber during 
Post Care phase of a programme. 
• 
The Start/Pause Light flashes Amber. 
• 
The start button 
 must be pressed to resume 
the programme including a delayed start. The 
progress lights will then change to show the 
current status and the Start/Pause light will stop 
flashing and turn green 
• 
During a delay phase the delay will continue to 
count down... 
• 
During the drying part of a programme, the time to 
end count continues but the colons do not flash.  
• 
During the post care part of a drying program, the 
programme will finish. Pressing the start/pause 
button will re-start a new programme. 
• 
Changing the Programmes knob will select a new 
programme and the Start/Pause Light will flash 
green. You can use this to select the Refresh 
programme 
 to cool the clothes if you find them 
dry enough.  
Press the start button 
 to begin new 
Programme 
• 
Note 
If you have a power cut, switch off the power or remove 
the plug. When power is restored,  press and hold the 
On/Off button
 until the dryer reactivates, then press the 
Start/Pause button.