Ampro Corporation Littleboard 550 User Manual
Chapter 4
BIOS Setup
LittleBoard 550
Reference Manual
67
♦
Drive D – [none], [HDD/CF on Pri Master], [CDROM on Pri Master], [HDD/CF on Pri Slave],
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec
Slave], [CDROM on Sec Slave], [USB HDD], or [USB CDROM]
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec
Slave], [CDROM on Sec Slave], [USB HDD], or [USB CDROM]
Table 4-2. Floppy Drive BIOS Settings
# of Floppy Drive(s)
BIOS Settings
None
• Set Drives A and B to [None]
(1) Non-USB Floppy
• Configure Drive A to floppy drive type (For example, [1.44MB, 3.5”] )
• Set Drive B to [None]
• Set Drive B to [None]
(1) USB Floppy
• Set USB Boot Support to [Enable]
• Set Drive A to [USB Floppy]
• Set Drive B to [None]
• Set Drive A to [USB Floppy]
• Set Drive B to [None]
(2) Floppy drives
(1 USB Floppy and
1 non-USB Floppy drive)
(1 USB Floppy and
1 non-USB Floppy drive)
• Set USB Boot Support to [Enable]
• Set one drive (Drive A or B) to the desired floppy drive type
• Set one drive (Drive A or B) to the desired floppy drive type
(For example, [1.44MB, 3.5”] )
• Set the other drive (Drive B or A) to [USB Floppy]
(2) Floppy drives
(2 non-USB Floppy drives)
(2 non-USB Floppy drives)
• Set either drive (Drive A or B) to desired floppy drive type
(For example, [1.44MB, 3.5”] )
• Set the other drive (Drive B or A) to desired floppy drive type
(For example, [1.44MB, 3.5”] )
Note: A standard 34-pin floppy cable has a twist in the cable wiring between the Floppy A and B
connectors, where Floppy B has the straight through cable (non-twist) and is the middle connector.
connectors, where Floppy B has the straight through cable (non-twist) and is the middle connector.
NOTE
Ampro does not recommend connecting a USB boot device to the
LittleBoard 550 through an external hub. Instead, connect the USB
boot device directly to the LittleBoard 550.
LittleBoard 550 through an external hub. Instead, connect the USB
boot device directly to the LittleBoard 550.
Any USB (block) device that emulates a hard disk drive can be used
when [USB HDD] is set as the drive option. This includes various
storage media types, such as USB hard disk drives, USB CD-ROMs,
CompactFlash
when [USB HDD] is set as the drive option. This includes various
storage media types, such as USB hard disk drives, USB CD-ROMs,
CompactFlash
™ cards, Secure Digital Memory Card™, and Flash or
Thumb drives. Refer also to Boot Order settings, USB Boot Support
under Advanced features, and USB (device enable) under On-Board
Controllers for USB Drive boot order, USB Boot Enable, and the
number of USB ports enabled, respectively.
under Advanced features, and USB (device enable) under On-Board
Controllers for USB Drive boot order, USB Boot Enable, and the
number of USB ports enabled, respectively.
♦
Drive E – [none], [HDD/CF on Pri Master], [CDROM on Pri Master], [HDD/CF on Pri Slave],
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]
♦
Drive F – [none], [HDD/CF on Pri Master], [CDROM on Pri Master], [HDD/CF on Pri Slave],
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]
♦
Drive G – [none], [HDD/CF on Pri Master], [CDROM on Pri Master], [HDD/CF on Pri Slave],
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]
[CDROM on Pri Slave], [HDD on Sec Master], [CDROM on Sec Master], [HDD on Sec Slave],
[CDROM on Sec Slave], [USB HDD], or [USB CDROM]