Amana D7824703 User Manual
Clips
Install Ice Maker
1.
Remove any shelves that may obstruct installation of
ice maker module.
Models with ice service rack
Slide ice service rack toward front of freezer until
screws are in middle of mounting holes. Gently pull ice
service rack away from freezer. Remove screws using
a
ice maker module.
Models with ice service rack
Slide ice service rack toward front of freezer until
screws are in middle of mounting holes. Gently pull ice
service rack away from freezer. Remove screws using
a
1
/
4
" hex nut driver. Insert provided plugs into screw
holes.
Bottom Freezer models
Remove freezer shelf and basket.
Top Freezer models
Remove freezer shelf.
Bottom Freezer models
Remove freezer shelf and basket.
Top Freezer models
Remove freezer shelf.
2.
Install hole plugs to properly position for ice maker.
Models with half-width freezer shelves
Push 2 oblong plugs provided, into 2 lowest shelf slots
on left side.
Models with full freezer shelves
Push 1 oblong plug provided, into lowest shelf slot on
each side.
Models with half-width freezer shelves
Push 2 oblong plugs provided, into 2 lowest shelf slots
on left side.
Models with full freezer shelves
Push 1 oblong plug provided, into lowest shelf slot on
each side.
3.
Remove ice maker from shipping carton and discard
packing material.
Important
Ice maker is shipped with arm down. This is correct
position for ice production. Do not force arm up or
down.
packing material.
Important
Ice maker is shipped with arm down. This is correct
position for ice production. Do not force arm up or
down.
4.
Slip stainless steel clip over rear wall of ice maker water
cup.
cup.
Water
cup
Stainless
steel clip
5.
Remove and discard 3 button plugs from left freezer
wall using flat blade screwdriver with blade covered with
masking tape.
wall using flat blade screwdriver with blade covered with
masking tape.
6.
Start
5
/
8
" sheet metal screw in top front hole, and top
rear hole in left wall. Leave heads out approximately
3
/
8
".
Insert screws
5
/
8
" sheet metal
screws here
Important
Ice maker can be installed one way only. Do not drill
additional holes.
Ice maker can be installed one way only. Do not drill
additional holes.
7.
Hold ice maker in position. Verify two outside electrical
flats line up with flats in receptacle on freezer back wall.
Insert wire harness plug into receptacle on rear wall
until locking fingers on plug snap into place. Slip ice
maker hanger over sheet metal screw.
flats line up with flats in receptacle on freezer back wall.
Insert wire harness plug into receptacle on rear wall
until locking fingers on plug snap into place. Slip ice
maker hanger over sheet metal screw.
Wire harness
receptacle
receptacle
Wire harness
plug
plug
Sheet metal
screw
screw
Ice maker
hanger
hanger
or
Wire harness
receptacle
receptacle
Wire harness
plug
plug
Sheet metal
screw
screw
Ice maker
hanger
hanger
8.
Ease ice maker water cup toward end of water fill tube.
Water fill tube fits under stainless steel clip. Water fill
tube must not be kinked. Water fill tube elbow should
extend
Water fill tube fits under stainless steel clip. Water fill
tube must not be kinked. Water fill tube elbow should
extend
3
/
8
" into ice maker water cup and must be
secured under stainless steel clip.
Water fill tube
Stainless
steel clip
Water
cup
cup
9.
Install remaining
5
/
8
" long sheet metal screw to secure
ice maker. Tighten all 3 screws.
10. Reinstall freezer shelf and and any baskets.
11. Position ice storage bucket on freezer shelf under ice
11. Position ice storage bucket on freezer shelf under ice
maker.