Alpine CDA 105 - 200 Watt AM/FM/MP3 iPod Receiver Owner's Manual
31
-EN
4.2ch (FRONT/REAR/SUBW.) System
1
After selecting CROSSOVER from the SOUND
ADJUST mode, press BAND to select the band to be
adjusted.
ADJUST mode, press BAND to select the band to be
adjusted.
4.2ch (FRONT/REAR/SUBW.) System / NORMAL (L=R)
setting items:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / INDIVIDUAL (L/R)
setting items:
L (SUB-W)-L / L (SUB-W)-R / M (REAR)-L /
M (REAR)-R / H (FRONT)-L / H (FRONT)-R
2
Press
or
to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
4.2ch (FRONT/REAR/SUBW.) System
Setting items:
20 Hz~200 Hz
3
Press SOURCE/
to adjust the slope.
Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
4
Turn the Rotary encoder to adjust the output level.
Adjustable output level: -12 to 0 dB.
5
Repeat steps 1 to 4 to make adjustment to the other
bands.
bands.
• While adjusting the CROSSOVER, you should consider the frequency
response of the connected speakers.
• About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system
You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
switch on the PXA-H100. For details, refer to the Owner’s Manual of
PXA-H100.
system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
switch on the PXA-H100. For details, refer to the Owner’s Manual of
PXA-H100.
Storing the Sound Field Adjustment Settings
The SOUND ADJUST Settings containing PARAMETER EQ/
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings can be
stored in the preset memory.
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings can be
stored in the preset memory.
1
When the settings of SOUND ADJUST have been
completed, select any one of the preset buttons
completed, select any one of the preset buttons
(1 through 6) in any item of the SOUND ADJUST
mode (e.g. CROSSOVER), press and hold the
desired preset buttons for at least 2 seconds.
mode (e.g. CROSSOVER), press and hold the
desired preset buttons for at least 2 seconds.
2
Turn the Rotary encoder to select PROTECT
YES/NO, and then press
/ENT to store the
adjusted contents.
PROTECT YES (Initial setting)
PROTECT NO
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
• While perform this operation, all adjusted contents of PARAMETER
• While perform this operation, all adjusted contents of PARAMETER
EQ/GRAPHIC EQ, T.CORRECTION and CROSSOVER will be
stored in the preset buttons.
stored in the preset buttons.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
Recalling the Stored Sound Field Adjustment
Settings
Settings
The stored SOUND ADJUST Settings contain PARAMETER EQ/
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings that are
stored in the preset memory.
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings that are
stored in the preset memory.
1
After selecting any item of the SOUND ADJUST
mode (e.g. CROSSOVER), press any one of the
preset buttons (1 through 6) that has your
desired characteristic in memory to recall the stored
settings.
mode (e.g. CROSSOVER), press any one of the
preset buttons (1 through 6) that has your
desired characteristic in memory to recall the stored
settings.
2
Press the preset buttons again to return to the
SOUND ADJUST mode.
SOUND ADJUST mode.
• While performing this operation, all adjustment contents of
PARAMETER EQ/GRAPHIC EQ, T.CORRECTION and
CROSSOVER stored in the preset buttons will be recalled.
CROSSOVER stored in the preset buttons will be recalled.