Dixon Aficio 1515 User Manual
Reception Features
42
4
Page Separation and Length
Reduction
Reduction
When the size of a received message
is longer than the paper loaded in the
machine, each page of the message
can be split and printed on several
sheets, or reduced and printed on a
single sheet. For example, this func-
tion splits the message if the message
length is 20 mm (0.79") or longer than
the paper used. The message is re-
duced if it is less than 20 mm (0.79").
When a message is split, an asterisk
(*) is inserted at the split position and
about 10 mm (0.39") of the split area is
duplicated on the top of the second
sheet.
is longer than the paper loaded in the
machine, each page of the message
can be split and printed on several
sheets, or reduced and printed on a
single sheet. For example, this func-
tion splits the message if the message
length is 20 mm (0.79") or longer than
the paper used. The message is re-
duced if it is less than 20 mm (0.79").
When a message is split, an asterisk
(*) is inserted at the split position and
about 10 mm (0.39") of the split area is
duplicated on the top of the second
sheet.
Note
❒ Your service representative can
customize this function with the
following settings:
• Reduction
• Print split mark
• Overprinting
• Overprinting length
• Guideline for split
following settings:
• Reduction
• Print split mark
• Overprinting
• Overprinting length
• Guideline for split
❒ You can adjust the overprinting
and reduction lengths within the
following ranges:
• Overprinting length: 4 mm (0.16"),
following ranges:
• Overprinting length: 4 mm (0.16"),
10 mm (0.39"), 15 mm (0.59")
• Guideline for split: 5-155 mm (5
mm steps)/0.2"-6.1" (0.2" steps)
TSI Print (Transmitting
Subscriber Identification Print)
Subscriber Identification Print)
Usually the sender's Fax Header is
printed on received messages. If the
sender has not programmed their Fax
Header, you will not be able to identi-
fy them. However, if you turn this
function on, the sender's Own Name
or Own Fax Number is printed in-
stead so you can find out where the
message came from. When you re-
ceive an Internet Fax, the e-mail ad-
dress of the sender is printed.
printed on received messages. If the
sender has not programmed their Fax
Header, you will not be able to identi-
fy them. However, if you turn this
function on, the sender's Own Name
or Own Fax Number is printed in-
stead so you can find out where the
message came from. When you re-
ceive an Internet Fax, the e-mail ad-
dress of the sender is printed.
Reference
p.55 “Initial Settings and Adjust-
ments”, Facsimile Reference <Basic
Features>
p.55 “Initial Settings and Adjust-
ments”, Facsimile Reference <Basic
Features>
Note
❒ You can turn this function on or off
in the User Parameters. See p.76
“User Parameters” (switch 02, bit
3).
“User Parameters” (switch 02, bit
3).
When There Is No Paper of the
Correct Size
Correct Size
If there is no paper in your machine
that matches the size of a received
message, the machine chooses a pa-
per size based upon the paper you
have available. For example, if your
machine has A4
that matches the size of a received
message, the machine chooses a pa-
per size based upon the paper you
have available. For example, if your
machine has A4
L and 8
1
/
2
"
×11"L
loaded and you receive a A5
K size
message, check the A5
K column of
the table below. The paper size at the
top has the highest priority. In this
case, since 8
top has the highest priority. In this
case, since 8
1
/
2
"
×11"L is a higher pri-
ority than A4
L, the message is print-
ed on 8
1
/
2
"
×11"L.
StellaC2-AEcombine-F_FM.book Page 42 Tuesday, January 13, 2004 1:22 PM