Manualsbrain.com
  1. Manuals
  2. Brands
  3. Datel
  4. 20A
  5. User Manual

Datel 20A User Manual

Download
Page of 22
USQ Series
USQ-1.2/20-D48 
1.2 
20 
25 
50 
±0.05% 
±0.05% 
48 
36-75  
0.63/0.87 
80% 
C33, P32
USQ-1.5/20-D48 
1.5 
20 
40 
65 
±0.05% 
±0.05% 
48 
36-75  
0.75/1.03 
85% 
C33, P32
USQ-1.8/20-D48 
1.8 
20 
50 
80 
±0.05% 
±0.05% 
48 
36-75  
0.88/1.23 
85% 
C33, P32
USQ-2.5/20-D48 
2.5 
20 
60 
75 
±0.05% 
±0.05% 
48 
36-75    
1.18/1.62 
87% 
C33, P32
USQ-3.3/20-D48 
3.3 
20 
70 
85 
±0.05% 
±0.05% 
48 
36-75  
1.54/2.1 
89% 
C33, P32
USQ-5/20-D24 
5 
20 
90 
125 
±0.05% 
±0.05% 
24 
18-36  
5.07/6.21 
90% 
C33, P32
USQ-5/20-D48 
5 
20 
90 
125 
±0.05% 
±0.05% 
48 
36-75  
2.33/3.13 
90% 
C33, P32
USQ-6.5/16-D24 
➆
 
6.5 
16 
90 
125 
±0.05% 
±0.05% 
24 
18-36 
4.95/6.60 
87.5% 
C33, P32
USQ-12/8.3-D24 
➇
 
12 
8.3 
135 
150 
±0.05% 
±0.05% 
24 
18-36 
4.61/6.08 
90% 
C33, P32
USQ-12/8.3-D48 
➇
 
12 
8.3 
120 
140 
±0.05% 
±0.05% 
48 
36-75  
2.30/2.41 
90% 
C33, P32
USQ-15/6.7-D24 
15 
6.7 
140 
155 
±0.05% 
±0.05% 
24 
18-36  
4.65/6.14 
91% 
C33, P32
USQ-15/6.7-D48 
15 
6.7 
145 
175 
±0.05% 
±0.05% 
48 
36-75  
2.30/2.42 
91% 
C33, P32
USQ-18/5.6-D24 
18 
5.6 
145 
175 
±0.05% 
±0.05% 
24 
18-36  
5.05/6.17 
91% 
C33, P32
USQ-18/5.6-D48 
18 
5.6 
145 
175 
±0.05% 
±0.05% 
48 
36-75  
2.30/2.42 
91% 
C33, P32
USQ-24/4.2-D24 
24 
4.2 
115 
130 
±0.05% 
±0.05% 
24 
18-36  
5.05/6.17 
92% 
C33, P32
USQ-24/4.2-D48 
24 
4.2 
115 
130 
±0.05% 
±0.05% 
48 
36-75  
2.27/3.18 
92% 
C33, P32
USQ-48/2.1-D48 
➆
 
48 
2.1 
115 
200 
±0.01% 
±0.01% 
48 
36-75  
2.27/3.03 
94.5% 
C33, P32
U SQ 3.3 20 D48 N
-
/
-
Remote On/Off Control Polarity: 
  Add "P" for positive polarity 
     (pin 2 open = converter on)   
  Add "N" for negative polarity 
     (pin 2 open = converter off)
Quarter-Brick Package
Output Configuration:
  U = Unipolar/Single
Nominal Output Voltage:
  1.2/1.5/1.8/2.5/3.3/5/12/15/18/24 Volts
Maximum Rated Output
   Current in Amps
Input Voltage Range:   
  D48 = 36-75 Volts (48V nominal)
  D24 = 18-36 Volts (24V nominal)
P A R T   N U M B E R   S T R U C T U R E
Performance Specifications and Ordering Guide
➀
Output
Input
2
➀
  Typical at T
A
 = +25°C under nominal line voltage and full-load conditions, unless otherwise  
  noted. All models are tested and specified with external output capacitors (1µF ceramic in  
  parallel with 10µF tantalum).
➁
  Contact DATEL for fixed output voltages (such as 2, 6.5, –5.2V) or higher output currents  
  (such as 12V @ 12.5A) other than those listed.
➂
  Ripple/Noise (R/N) is tested/specified over a 20MHz bandwidth. Output noise may be further 
  reduced with the installation of additional external output filtering. See I/O Filtering, Input  
  Ripple Current, and Output Noise for details.
➃
  The load-regulation specs apply over the 0-100% range. All models in the USQ Series have  
  no minimum-load requirements and will regulate within spec under no-load conditions (with  
  perhaps a slight increase in ripple/noise). Additionally, 1.2V, 1.5V, 1.8V, 2.5V and 5V models  
  are unconditionally stable, including start-up and short-circuit-shutdown situations, with  
  capacitive loads up to 25,000µF.  The 12V,15V,18V and 24V models are unconditionally stable 
  with capacitive loads up to 470µF at full load.
➄
  Contact DATEL for V
IN
 ranges other than those listed.
➅
  The two listed dc currents are for the following conditions: full load/nominal input voltage and  
  full load/low line voltage. The latter is usually the worst-case condition for input current.
➆
  Contact DATEL for availability and further information on these models.
➇
  These models are discontinued. Refer to DATEL's ULQ and UVQ series for alternate models.
 
I/O Connections
 
Pin  Function P32 
  1 
–Input
  2  Remote On/Off*
  3 
+Input
  4 
–Output
  5 
–Sense
  6 
Output Trim 
  7 
+Sense
  8 
+Output
* The Remote On/Off 
can be provided with 
either positive (standard) 
or negative (optional) 
polarity. 
M E C H A N I C A L   S P E C I F I C A T I O N S
Case C33
1.45 (36.83)
BOTTOM VIEW
1
2
3
8
7
6
5
4
(4) 0.170 DIA. 
#M3 THD. THRU
WITH 0.090 
THREAD RELIEF
OPEN-FRAME, CAST 
ALUMINUM CASE
BAR CODE AND 
SERIAL NUMBER 
APPLIED TO
THIS SURFACE. 
MODEL NUMBER ON 
OPPOSITE SURFACE.
0.15 MIN (3.81)
0.40 MAX.
(10.16)
DIMENSIONS ARE IN INCHES (MM)
STANDOFF
0.015 (0.38)
2.28 (57.91)
PINS 1-3, 5-7:
  0.040 ±0.001 (1.016 ±0.025)
PINS 4, 8: 
   0.062 ±0.001 (1.575 ±0.025)
A
B
B
0.300
(7.62)
1.03 (26.16)
0.600 
(15.24)
B
B
1.860 (47.24)
2.00 (50.80)
A
A
0.600 (15.24)
4 EQ. SP. @ 
0.150 (3.81)
0.10
(2.54)
*
* USQ SERIES HEATSINKS ARE AVAILABLE IN 3 HEIGHTS:
0.25 (6.35), 0.50 (12.70) AND 1.00 (25.4)
1.45
(36.83)
2.28
(57.91)
MATERIAL: BLACK ANODIZED ALUMINUM
1.03
(26.16)
1.860
(47.24)
0.140 DIA. (3.56) (4 PLACES)
Optional 
Heat Sink
➀ 
DATEL conforms to industry-standard quarter-brick pinout (see Figure 20).
➁ 
A "baseplate only" model with a maximum height of 0.375" (9.53mm) is 
 
available with the addition of an "H" suffix. Contact DATEL.
 
R/N (mVp-p) ➂ 
Regulation (Max.)
 
 
 
 
 
 
 
 
 
 
 
 
Package
 
 
V
OUT 
➁
 
I
OUT
 
 
 
  
 
V
IN
 Nom. 
Range 
I
IN 
➅ 
 
(Case,  
  Model 
(Volts) 
(Amps) 
Typ. 
Max. 
Line 
Load ➃ 
(Volts) ➄ 
(Volts) ➄ 
(Amps) 
Efficiency 
Pinout)
Heat Sink Ordering Information
Heat Sink Height 
DATEL Part Number
0.25 inches (6.35mm) 
HS-QB25 
0.50 inches (12.70mm) 
HS-QB50
1.00 inches (25.40mm) 
HS-QB100
All heat sinks include 4 mounting screws and a thermal pad. 
If using heatsinks other than DATEL's HS-QB series, the screw length should accomo-
date the 0.090 thread relief.
Negative Trim: 
  Contact DATEL 
D
2 0 A ,   S I N G L E   O U T P U T   D C / D C   C O N V E R T E R S
OBSOLETE PRODUCT
Contact Factory for Replacement Model