Garmin Vector S Owner's Manual
Analyze your data: You can view more detailed information
about your activity, including time, distance, elevation, heart
rate, calories burned, cadence, an overhead map view, pace
and speed charts, and customizable reports.
NOTE: Some data requires an optional accessory such as a
NOTE: Some data requires an optional accessory such as a
heart rate monitor.
Plan your training: You can choose a fitness goal and load
one of the day-by-day training plans.
Share your activities: You can connect with friends to follow
each other's activities or post links to your activities on your
favorite social networking sites.
Disconnecting the USB Cable
If your device is connected to your computer as a removable
drive or volume, you must safely disconnect your device from
your computer to avoid data loss. If your device is connected to
your Windows® computer as a portable device, it is not
necessary to safely disconnect.
1
Complete an action:
• For Windows computers, select the Safely Remove
• For Windows computers, select the Safely Remove
Hardware icon in the system tray, and select your device.
• For Mac® computers, drag the volume icon to the trash.
2
Disconnect the cable from your computer.
Device Information
Vector Device Care
NOTICE
Keep the components clean and free of debris.
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that
can damage plastic components and finishes.
Do not submerge or pressure wash the components.
Do not store the device where prolonged exposure to extreme
Do not submerge or pressure wash the components.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Replace components with Garmin parts only. See your Garmin
Replace components with Garmin parts only. See your Garmin
dealer or the Garmin website.
Removing the Pedal Pod and Pedal
NOTICE
Do not attempt to pry the cable from the spindle.
Use the pedal wrench
À
to slowly loosen the pedal
Á
.
NOTE: The spindle and crank for the left pedal has a left-
handed (reverse) thread.
As you unscrew the pedal, the pedal pod cable disengages
As you unscrew the pedal, the pedal pod cable disengages
from the spindle.
When you install Vector again, you must recalibrate the system.
Replacing the Pedals and Cartridges
Before you can start this task, you must obtain a cartridge axle
tool (available from Exustar™ or Shimano®), 8 mm hex nut
driver, 15 mm pedal wrench, and bike grease.
NOTICE
Other compatible tools can be used. Use care not to damage
any of the Vector components.
If your pedals are damaged or show significant wear, you can
replace the pedals, cartridges, and related hardware
components.
NOTE: Pedal and cartridge replacement is the same for the
NOTE: Pedal and cartridge replacement is the same for the
Vector and Vector S systems. You should keep the left pedal
parts separate from the right pedal parts.
1
Remove the pedals and pedal pods from your bike
).
2
Unscrew the pedal body
À
from the cartridge
Á
using the
cartridge axle tool.
NOTE: The right pedal has a left-handed (reverse) thread.
NOTE: The right pedal has a left-handed (reverse) thread.
3
Remove the pedal body.
4
While securely holding the spindle
Â
with a pedal wrench,
use the hex nut driver to remove the nut
Ã
and washer
Ä
.
5
Separate the cartridge from the spindle.
6
Remove the brass spacer ring
Å
and dust seal
Æ
.
NOTE: The Vector S right pedal does not include brass
spacer, and the dust seal is reversed.
7
Remove old grease from the spindle.
8
Slide the new dust seal and brass spacer ring over the
spindle.
The tapered side of the dust seal and brass spacer ring must
The tapered side of the dust seal and brass spacer ring must
face the base of the spindle.
4
Device Information