Bosch 24" Compact Condensation Dryer Axxis WTB86201UC Owner's Manual
13
▯
If installed in an upper floor of a multi-story building,
the dryer should be installed on a drained floor to
prevent water damage to lower floors in the event of a
leak.
Electrical Connections
Power Cord
The attached power cord is a standard 4-wire dryer cord
The attached power cord is a standard 4-wire dryer cord
and is UL approved and listed in the USA and Canada. It
meets the following requirements:
▯
208-240 volt rated (minimum);
▯
30 amps;
▯
Type SRDT or DRT (UL 2158A).
NOTICE: If your specific installation requires a 3-wire
power cord follow the installation instructions for such in
the next section of this manual.
ALL ELECTRICAL CONNECTIONS AND CIRCUITS
9
WARNING
ELECTRIC SHOCK
▯
Do not pull on the power cord to unplug the
dryer.
▯
Protect the power cord from physical damage
such as being twisted, kinked, pinched, or walked
on for example.
▯
DO NOT use an extension cord or an adapter to
connect the dryer to the power supply.
▯
Make sure:
- The power cord fits into the outlet/receptacle.
- The home’s internal power supply circuit wire
- The power cord fits into the outlet/receptacle.
- The home’s internal power supply circuit wire
size is sufficient and electrically grounded.
▯
The outlet/receptacle used to power the dryer
must be connected to an individual 30 amps
Branch Circuit.
▯
Do not cut, remove or bypass the grounding
prong on the power cord end.
▯
Do not modify the plug provided. If the plug will
not fit into the outlet/receptacle have it inspected
by a qualified electrician.
▯
The power cord must only be replaced by a
qualified technician or licensed electrician to help
avoid a fire/electric shock hazard.
Replacement power cords are available through
our Customer Service department.
▯
Use only a UL listed 30 amps power cord.
▯
Do not reuse old power cord.
▯
Do not make a sharp bend or crimp wiring or
conductors at connections.
▯
Use only a 4-wire/conductor power cord when
the appliance is installed in a mobile home,
recreational vehicle, in a new branch-circuit
installations or where the local codes do not
permit grounding through the neutral.
9
WARNING
ELECTRIC SHOCK
To reduce the risk of electrical shock:
To reduce the risk of electrical shock:
▯
Only pull out the main cable by the plug and
never by the cable, as this could damage it.
▯
Never touch or hold the main plug with wet
hands.
▯
Never unplug the main plug during operation.
9
WARNING
ELECTRIC SHOCK
Improper connection of the ground may result in
Improper connection of the ground may result in
electric shock. Have the appliance checked by a
qualified technician or licensed electrician if you are
in doubt as to whether the dryer has been properly
grounded.
Grounding Instructions
This appliance must be electrically grounded. In the
This appliance must be electrically grounded. In the
event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of
least resistance for electric current.
This appliance is equipped with a cord that has an
This appliance is equipped with a cord that has an
equipment grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that
The plug must be plugged into an appropriate outlet that
is properly installed and grounded in accordance with all
local codes and ordinances.
If a ground fault circuit breaker is used, ensure it has this
If a ground fault circuit breaker is used, ensure it has this
symbol:
z
.
This symbol guarantees compliance with all current
regulations.
SAVE THESE INSTRUCTIONS!
SAVE THESE INSTRUCTIONS!
Connecting a 3-wire power supply cord
The power cord must meet the following requirements:
The power cord must meet the following requirements:
▯
208-240 volt rated (minimum);
▯
30 amps;
▯
Type SRDT or DRT (UL 2158A).