Bosch Appliances Home Security System ICP-CC404 User Manual
ICP-CC404 | Installation Guide | 15.0 System Reporting Information
60 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
Example
All eight zones are programmed for lockout dialer
with a Swinger Shutdown Count of 6. If Zone 1
activates an alarm, the Swinger Shutdown Count
decreased to 5 when the control panel calls.
with a Swinger Shutdown Count of 6. If Zone 1
activates an alarm, the Swinger Shutdown Count
decreased to 5 when the control panel calls.
If Zone 1 reactivates the dialer, the Swinger
Shutdown Count is decreased to 4. If Zone 1
reactivates the dialer three more times, the Swinger
Shutdown Count is 1.
Shutdown Count is decreased to 4. If Zone 1
reactivates the dialer three more times, the Swinger
Shutdown Count is 1.
If Zone 2 activates an alarm, the Swinger Shutdown
Count decreases to 0, which locks out Zone 2 from
activating the dialer until the system resets. At this
point, the Swinger Shutdown Count for the Dialer
resets to 6 and the process of swinger shutdown for
the remaining zones, including Zone 1, begins again
until all zones are locked out.
Count decreases to 0, which locks out Zone 2 from
activating the dialer until the system resets. At this
point, the Swinger Shutdown Count for the Dialer
resets to 6 and the process of swinger shutdown for
the remaining zones, including Zone 1, begins again
until all zones are locked out.
15.0 System Reporting
Information
This section covers basic housekeeping features of the
system.
system.
15.1 Zone Status – Bypass Reports
Program the Zone Bypass Report value in
Location
325 (the default value is 9) and the Zone Bypass
Restore Report value in
Restore Report value in
Location 326 (default 8).
A zone is bypassed when it is manually isolated.
Refer to Section 4.11 Isolating Zones on page 21 for
information on isolating zones. A Zone Bypass
Report (Contact ID Event Code 570) is sent at the
end of Exit Time for any zone that was manually
isolated. A 24-Hour Zone sends a Zone Bypass
Report when the zone is selected to be isolated.
Refer to Section 4.11 Isolating Zones on page 21 for
information on isolating zones. A Zone Bypass
Report (Contact ID Event Code 570) is sent at the
end of Exit Time for any zone that was manually
isolated. A 24-Hour Zone sends a Zone Bypass
Report when the zone is selected to be isolated.
A Zone Bypass Restore Report is sent when the
system is disarmed. All bypassed zones are cleared
when the system is disarmed.
system is disarmed. All bypassed zones are cleared
when the system is disarmed.
The Bypass Code parameter is used as the expansion
digit in 4+2 Formats. It has no effect on Contact ID
Format because a Zone Bypass is always sent as
Event Code 570.
digit in 4+2 Formats. It has no effect on Contact ID
Format because a Zone Bypass is always sent as
Event Code 570.
If Zone Bypass Reports are not required,
program Locations 325 and 326 as 0.
program Locations 325 and 326 as 0.
15.2 Zone Status – Trouble Reports
Program the Zone Trouble Report value in
Location 327 (the default value is 2) and the Zone
Trouble Restore Report value in
Location 327 (the default value is 2) and the Zone
Trouble Restore Report value in
Location 326
(default
3).
A zone is in trouble when it is unsealed at the end of
Exit Time. A Sensor Trouble Report (Contact ID
Event Code 380) is sent to indicate that one or more
zones were automatically isolated by the system. 24-
Hour Zones that are unsealed at the end of Exit Time
do not send a Sensor Trouble Report because the
restore for that zone is still outstanding.
Exit Time. A Sensor Trouble Report (Contact ID
Event Code 380) is sent to indicate that one or more
zones were automatically isolated by the system. 24-
Hour Zones that are unsealed at the end of Exit Time
do not send a Sensor Trouble Report because the
restore for that zone is still outstanding.
A Sensor Trouble Restore Report is sent for Burglary
Zones when the zone is resealed or the next time the
system is disarmed (whichever happens first). A 24-
Hour Zone sends a restore signal only when it is
resealed.
Zones when the zone is resealed or the next time the
system is disarmed (whichever happens first). A 24-
Hour Zone sends a restore signal only when it is
resealed.
The Trouble code parameter is used as the expansion
digit in 4+2 Format. It has no effect on Contact ID
Format because a Sensor Trouble Report is always
sent as Event Code 380.
digit in 4+2 Format. It has no effect on Contact ID
Format because a Sensor Trouble Report is always
sent as Event Code 380.
If Sensor Trouble Reports are not
required, program Locations 327 and
328 as 0.
required, program Locations 327 and
328 as 0.
15.3 Zone Status – Sensor Watch
Reports
Program the Sensor Watch Report value in
Location 329 (the default value is 4) and the Sensor
Watch Restore Report value in
Location 329 (the default value is 4) and the Sensor
Watch Restore Report value in
Location 326
(default
8).
A Self Test Failure Report (Contact ID Event Code
307) is sent to the base station receiver when a zone
was not activated during the Sensor Watch Time
programmed in Locations 408 and 409 (refer to
Section 17.7 Sensor Watch Time on page 71). This report
continues to be sent (according to the frequency of
the Sensor Watch Time) until the fault is corrected.
307) is sent to the base station receiver when a zone
was not activated during the Sensor Watch Time
programmed in Locations 408 and 409 (refer to
Section 17.7 Sensor Watch Time on page 71). This report
continues to be sent (according to the frequency of
the Sensor Watch Time) until the fault is corrected.
To clear the fault and stop any additional reporting,
you must unseal and reseal the zone that registered
the fault. Use the Sensor Watch Time in Locations
408 and 409 to set the number of days a zone can
remain sealed without registering a fault. Refer to
Section 14.3.4 Zone Options 1 on page 57 to select zones
to be monitored by the Sensor Watch feature.
you must unseal and reseal the zone that registered
the fault. Use the Sensor Watch Time in Locations
408 and 409 to set the number of days a zone can
remain sealed without registering a fault. Refer to
Section 14.3.4 Zone Options 1 on page 57 to select zones
to be monitored by the Sensor Watch feature.
If Self Test Failure Reports are not
required, program Locations 329 and
330 as 0.
required, program Locations 329 and
330 as 0.
15.4 Zone Status – Alarm Restore Code
Program the Alarm Restore Code value in
Location 331.
Location 331.
The default value is
14.
If Zone Alarm Restore Reports are required, program
this location as 14. If not, program this location as 0.
this location as 14. If not, program this location as 0.