Bosch Appliances Home Security System ICP-CC404 User Manual
ICP-CC404 | Installation Guide | 21.0 Specifications
84 Bosch
Security
Systems,
Inc. | 12/08 | F01U089401-02
21.0 Specifications
Table 66:
Specifications
Temperature Range
0
o
C to +45
o
C
(+32
o
F to +113
o
F)
Humidity
10% to 95%
Power Source
TF008 Plug Pack –
240 VAC/18 VAC @ 1.3 A
240 VAC/18 VAC @ 1.3 A
Standby Current
65 mA
Current Draw In Alarm
115 mA
Current Draw In Alarm
with Codepad
with Codepad
105 mA
Backup Battery
6 Ah/12 VDC Rechargeable
sealed lead acid battery
sealed lead acid battery
Dimensions (case,
packed in carton)
packed in carton)
30.6 cm x 26.2 cm x 8.4 cm
(12.1 in. x 10.3 in. x 3.3 in.)
(12.1 in. x 10.3 in. x 3.3 in.)
Weight
2.5 kg (5.5 lb)
Supplier Code
N771
New Zealand Telepermit
PTC 211/98/085
The Austel permit issued for this product
is subject to the following conditions:
The ICP-CC404 Control Panel can only
be powered by a Bosch Security
Systems, Inc. TF008 Plug Pack (Approval
Number Q92128).
is subject to the following conditions:
The ICP-CC404 Control Panel can only
be powered by a Bosch Security
Systems, Inc. TF008 Plug Pack (Approval
Number Q92128).
21.1 Warranty
Statement
Bosch Security Systems, Inc. warrants this product to
be free from defects in material and workmanship for
a period of three years from the date of manufacture
as indicated by the date stamp or the serial number
on the product.
be free from defects in material and workmanship for
a period of three years from the date of manufacture
as indicated by the date stamp or the serial number
on the product.
Defective units returned by the purchaser at their
own expense during this period will be repaired or
replaced at the option of the manufacturer. The repair
or replacement is free of charge provided that the
defects were not incurred during shipping or
handling, or the damage was not due to causes
beyond the control of Bosch Security Systems, Inc.,
such as lightning, excessive voltage, mechanical
shock, or damage arising out of abuse, alteration, or
improper application of the equipment.
own expense during this period will be repaired or
replaced at the option of the manufacturer. The repair
or replacement is free of charge provided that the
defects were not incurred during shipping or
handling, or the damage was not due to causes
beyond the control of Bosch Security Systems, Inc.,
such as lightning, excessive voltage, mechanical
shock, or damage arising out of abuse, alteration, or
improper application of the equipment.
21.2 Advice to Users
The Austel permit issued for this product is subject to
this condition:
this condition:
The ICP-CC404 Control Panel can only be powered
by a TF008 Plug Pack (Approval Number Q92128).
by a TF008 Plug Pack (Approval Number Q92128).
21.3 New Zealand Telepermit Notes
• The grant of a telepermit for a device does not
indicate telecom acceptance of responsibility for
the correct operation of the device under all
operating conditions.
the correct operation of the device under all
operating conditions.
• This equipment shall not be used in any manner
that could constitute a nuisance to other telecom
customers.
customers.
• Disconnect this equipment immediately if it
becomes physically damaged and arrange for its
disposal or repair.
disposal or repair.
• The transmit level from this device is set at a
fixed level, so there might be circumstances
where the performance is less than optimal.
Before reporting such occurrences as faults,
please check the line with a standard
telepermitted telephone and do not report a fault
if the telephone performance is satisfactory.
where the performance is less than optimal.
Before reporting such occurrences as faults,
please check the line with a standard
telepermitted telephone and do not report a fault
if the telephone performance is satisfactory.
• This device is equipped with pulse dialing while
the telecom standard is DTMF tone dialing.
There is no guarantee that telecom lines will
always continue to support pulse dialing.
Use of dialing, when this equipment is connected
to the same line as other equipment, can give rise
to bell tinkle or noise and can also cause a false
answer condition. If problems such as this occur,
the user should not contact the Telecom Faults
Service.
There is no guarantee that telecom lines will
always continue to support pulse dialing.
Use of dialing, when this equipment is connected
to the same line as other equipment, can give rise
to bell tinkle or noise and can also cause a false
answer condition. If problems such as this occur,
the user should not contact the Telecom Faults
Service.
• This equipment is set up to carry out test calls at
pre-determined times. These test calls interrupt
other calls that might be set up on the line at the
same time. Discuss the timing set for these test
calls with the installer.
The timing set for test calls from this equipment
may be subject to drift. If this proves to be
inconvenient and your calls are interrupted,
discuss the problem of timing with the equipment
installer. Do not report the matter as a fault to
Telecom Faults Service.
other calls that might be set up on the line at the
same time. Discuss the timing set for these test
calls with the installer.
The timing set for test calls from this equipment
may be subject to drift. If this proves to be
inconvenient and your calls are interrupted,
discuss the problem of timing with the equipment
installer. Do not report the matter as a fault to
Telecom Faults Service.
• This equipment shall not be set up to make
automatic calls to the Telecom 111 Emergency
Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to
other Telecom customers.
Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to
other Telecom customers.
• In the event of any problem with this device,
disconnect the system battery, AC mains supply,
and the telephone line. The user must arrange
with the supplier of the device for the necessary
repairs.
If the matter is reported to telecom as a wiring
fault and the fault is proven to be due to this
product, a call-out charge is incurred.
and the telephone line. The user must arrange
with the supplier of the device for the necessary
repairs.
If the matter is reported to telecom as a wiring
fault and the fault is proven to be due to this
product, a call-out charge is incurred.