Monster Cable Monster iEZClick 127563.00 Leaflet
Product codes
127563.00
Hold
Previous
Track/
Playlist
Next
Track/
Playlist
Hold
Volume Up
Volume Down
Play/Pause
iPod On/Off
rm 162822
Hold Switch Shown in
“Unlocked” Position
Hold Switch Shown in
“Locked” Position
Wireless
Receiver
Insert Receiver
as Shown to
Avoid Damage
to Dock Connector
and/or Receiver
Detach Belt Clip
Before Attaching
Wrist Strap
MONSTER SAFETY TIP
Do not wear headphones or attempt to operate the
iEZClick during potentially dangerous activities. Please be
aware of your surroundings at all times.
iEZClick
™
Wireless Remote Control
2-Piece RF Transmitter-Receiver System
for iPod
®
iEZClick
™
Wireless Remote
Control Features/Contents
• Easy-to-use, familiar iPod
®
-style button layout
with tactile control
• Controls for Volume, Track, Hold, Previous
and Next Playlists
• Wireless RF technology offers up to 30-foot range*
• Operates through walls, doors, bags,
• Operates through walls, doors, bags,
jackets, etc.*
• Convenient belt clip and wrist strap
for on-the-go use
• Water-resistant design with rugged
rubberized holder
INSTRUCTIONS
Unlock Remote (Hold Switch)
Your new iEZClick Remote comes supplied with
the battery pre-installed and the Hold switch on.
the battery pre-installed and the Hold switch on.
(Note: The iEZClick wireless receiver does
not use a battery, as power is supplied
from the iPod.)
from the iPod.)
1. To begin use, slide the Hold switch on the
iEZClick remote to hide the red-colored
indicator under the Hold switch.
indicator under the Hold switch.
Connect the Wireless Receiver
1. You can plug the iEZClick wireless receiver
to your iPod docking connector while the iPod
is on or off without any risk of damage.
is on or off without any risk of damage.
2. Make sure iPod power is on.
3. Navigate to your first song of choice using
your iPod controls. (Note: To begin using
iEZClick, your iPod must already be in a playlist.)
iEZClick, your iPod must already be in a playlist.)
Remote Control of Your iPod
THANK YOU for purchasing Monster’s iEZClick
™
2-piece RF Transmiter-Receiver System. Using
wireless RF (radio frequency) technology,
the iEZClick lets you control your iPod when it’s
buried in a pocket, bag, or jacket during travel,
or when you’re engaging in outdoor activities.
The iEZClick controls are large and widely spaced
so you can easily control your iPod with gloves
on or simply by touch without looking. The iEZClick
RF signals can also travel through walls, floors
and doors* so you can remotely control your
iPod from a different room or through backpacks,
pockets, jackets, etc.*
The Monster iEZClick can switch your iPod
on and off, skip tracks, adjust volume, change
playlist and pause and resume playback.
The large center button (showing the Monster
wireless RF (radio frequency) technology,
the iEZClick lets you control your iPod when it’s
buried in a pocket, bag, or jacket during travel,
or when you’re engaging in outdoor activities.
The iEZClick controls are large and widely spaced
so you can easily control your iPod with gloves
on or simply by touch without looking. The iEZClick
RF signals can also travel through walls, floors
and doors* so you can remotely control your
iPod from a different room or through backpacks,
pockets, jackets, etc.*
The Monster iEZClick can switch your iPod
on and off, skip tracks, adjust volume, change
playlist and pause and resume playback.
The large center button (showing the Monster
®
“M” logo) is a multi-purpose control.
With iEZClick, wireless remote control has never
been easier or more effective.
With iEZClick, wireless remote control has never
been easier or more effective.
To Turn iPod Power On or Off
1. Press and hold the button to turn iPod off.
2. Press and hold the button to turn iPod on.
2. Press and hold the button to turn iPod on.
To Play/Pause Music
1. Press the center button briefly
to begin playback.
2. Press the center button briefly again.
Playback will pause.
To Disable iEZClick
Controls (Remote Hold)
1. To activate Hold on the iEZClick, slide the Hold
switch on the iEZClick remote to display
the red-colored indicator under the Hold
switch. The iEZClick’s buttons will be disabled,
while the iPod’s click wheel controls will
continue working.
the red-colored indicator under the Hold
switch. The iEZClick’s buttons will be disabled,
while the iPod’s click wheel controls will
continue working.
2. Slide the Hold switch back up to resume normal
iEZClick control.
To Attach Wrist Strap
Your iEZClick Remote Control comes supplied
with a wrist strap for convenient operation.
with a wrist strap for convenient operation.
1. Slide the wrist strap through the slots
on the iEZClick casing as shown.
2. Position the iEZClick Remote Control on your
arm in a comfortable spot, and tighten
the wrist strap.
(CAUTION: DO NOT OVERTIGHTEN!
Setting the wrist strap too tight can
cut off blood circulation.)
the wrist strap.
(CAUTION: DO NOT OVERTIGHTEN!
Setting the wrist strap too tight can
cut off blood circulation.)
To Detach Belt Clip
1. Hold iEZClick sideways in both hands.
2. Press one side of the clip free from iEZClick
2. Press one side of the clip free from iEZClick
tab with both thumbs and pull outward.
3. Reverse process to re-attach.
To Change Remote Battery
1. Unscrew both screws on the iEZClick’s battery
compartment and remove the cover.
2. Remove the button-size battery.
3. Replace with a fresh CR2032 Lithium battery.
3. Replace with a fresh CR2032 Lithium battery.
Pay careful attention to polarity (the and
sides of the battery). The remote will only
work when properly oriented. Return
the battery compartment cover to its usual
position and screw in.
sides of the battery). The remote will only
work when properly oriented. Return
the battery compartment cover to its usual
position and screw in.
Interference from Other
iEZClick Remotes
Your iEZClick remote and wireless receiver are
designed to work together seamlessly. If you’re
experiencing interference or unwanted commands
from other iEZClick remote users, the following
should help resolve the problem:
designed to work together seamlessly. If you’re
experiencing interference or unwanted commands
from other iEZClick remote users, the following
should help resolve the problem:
Pairing
1. Plug iEZClick wireless
receiver into iPod
dock connector.
dock connector.
2. Insert end of paper
clip into small hole in
the iEZClick wireless
receiver and hold down.
the iEZClick wireless
receiver and hold down.
3. Press and release any button on the iEZClick
remote to activate pairing.
4. Use remote normally and check if any unwanted
interference or commands occur.
*Range determined by product specifications and other environmental variables
To Skip to Next/Previous Track
1. Press the or button once briefly to skip
a single track.
To Fast Forward/Rewind Track
1. Press and hold the or button.
To Skip to Next/Previous Playlist
1. Press the button and the button
simultaneously to skip to Next Playlist.
2. To skip to Previous Playlist, press the button
and the button simultaneously.
To Adjust Volume
1. Press the button to increase or the button
to decrease volume.
To Disable iPod Controls
(iPod Hold)
When carrying your iPod in a pocket or purse,
disabling its click wheel controls by activating
the iPod’s Hold switch function will prevent
accidental button pushing. This ensures that only
the iEZClick Remote can control the iPod.
disabling its click wheel controls by activating
the iPod’s Hold switch function will prevent
accidental button pushing. This ensures that only
the iEZClick Remote can control the iPod.
1. To activate Hold
on the iPod, slide
the Hold switch
down to display
the red-colored
indicator under
the Hold switch. The
iPod’s built-in controls
will be disabled, while
the iEZClick controls will
continue working.
the Hold switch
down to display
the red-colored
indicator under
the Hold switch. The
iPod’s built-in controls
will be disabled, while
the iEZClick controls will
continue working.
2. Slide the Hold switch back to resume use
of iPod controls.
Un-Pairing
If you paired your iEZClick remote and wireless
receiver due to interference, you can also un-pair
them to return them to original factory settings if
needed by doing the following:
receiver due to interference, you can also un-pair
them to return them to original factory settings if
needed by doing the following:
1. Plug iEZClick wireless receiver into
iPod dock connector.
2. Insert end of paper clip into small hole in the
iEZClick wireless receiver and hold down for 10
seconds.
seconds.
3. DO NOT PRESS any button on the iEZClick
remote during the 10 seconds.
4. After 10 seconds, your iEZClick
remote and receiver will have
been restored to factory settings.
been restored to factory settings.
We invite you to visit the
Monsters at:
MonsterCable.com
Get All the Performance You Paid For
™
Monster Cable Products, Inc.
455 Valley Drive Brisbane, CA 94005 USA
1-877-800-8989
Engineered in the USA and manufactured for Monster
to its quality specifications.
Made in China.
*Range determined by product specifications and other environmental variables