Bosch Appliances Video Game Controller D9412GV2 User Manual

Page of 158
D9412GV2/D7412GV2 | Program Entry Guide | 6.0  GV2AUX 
EN | 135 
 
 
Bosch Security Systems, Inc. | 10/08 | F01U003636-04 
If events are to be routed to an SDI Path but not to an 
IP Address, allow the setting for Path # IP Add# to 
remain at 0. Path # Poll RatePath # Ack Wait, and 
Path # Retry Count must be programmed. 
 
6.5 
Programming Path Numbers and 
IP Addresses for Enhanced 
Communications 
 
Enhanced communications is the ability to 
communicate by some means other than the 
standard digital dialer. In this section, programmable 
parameters allow you to define up to four separate 
enhanced communication paths to which events can 
be routed. To route an event (such as an Alarm or 
Trouble) to an enhanced communication path, 
additional programming must also be completed in 
Section 
Path # IP Add1 
Default: 
Selection: 
0 to 255 
Enter the first three digits of the IP 
address. Leading zeros are not 
required. 
0 to 255 
2.3 Routing on page 15 anSection 2.4 
 
 
If using IP Addresses as the 
communication means for UL 864 
Enhanced Comm 
Commercial Fire applications, set Path 
# IP Add
 1 through 4 as necessary. 
Default: 
No 
 
Path # IP Add 1 and the next three items determine 
the IP addresses for each of the four enhanced 
communication paths available when using the 
D5200.  
Selection: 
Yes or No 
Enable enhanced communications 
over the SDI bus. 
Yes 
No 
Do not enable enhanced 
communications over the SDI bus. 
An IP address has  four fields. Each field has a range 
of 0 to 255. For example, an IP address is expressed 
as 110.227.64.190. The D5200 programmer splits the 
IP address into four programmable fields (refer to 
 
 
If using IP Addresses as the 
communication means for UL 864 
Commercial Fire applications, set this 
parameter to Yes
Figure 10). Contact your network administrator to 
obtain the appropriate IP Address to contact a central 
station receiver. 
 
Determines if the control panel allows enhanced 
communications over the SDI bus. 
Figure 10: Path # IP Add1 to Add4 
 
 
110.227.64.190
Path # IP Add1
Path # IP Add2
Path # IP Add3
Path # IP Add4
•  Modem Format must be set to Yes 
when using enhanced communications. 
•  Enable Ext Modem must be set to No 
if enhanced communications are used. 
•  Enhanced Comm must be set to No if 
an external modem is used. 
 
 
 
To disable Enhanced Routing completely 
 
over an SDI path, RG#Primary SDI
Path # IP Add2 
RG#Backup SDI, and Enhanced Comm 
 
prompts must all be set to No
Default: 
Events can be routed to as many as four available 
enhanced communication paths through the SDI bus. 
If an event (or group of events) is routed to an SDI 
path, the number entered in Primary Device 
determines which SDI path is used (provided that 
RG# PrimPrimary SDI was set to Yes in Routing). 
Selection: 
0 to 255 
Refer to Path 1 IP Add1
Path # IP Add3 
Default: 
If events are to be routed to an IP address (in a 
private LAN or WAN application), determine which 
path is used (Path 1 to Path 4), and enter the 
appropriate IP Address for that path (refer to Path # 
IP Add1
 to Path # IP Add4). 
Selection: 
0 to 255 
Refer to Path 1 IP Add1