Bosch Appliances Video Game Controller D9412GV2 User Manual
D9412GV2/D7412GV2 | Program Entry Guide | 7.0 RADXAXS
EN | 144
Bosch Security Systems, Inc. | 10/08 | F01U003636-04
D#CC#Scope
7.0 RADXAXS
Default:
Blank
7.1 Door Profile
Selection:
Blank, 1 to 8
This programming category is used to:
1 to 8
Determines disarming rights. The
user’s access level and the CC #
Scope determines which areas are
disarmed.
user’s access level and the CC #
Scope determines which areas are
disarmed.
•
•
•
•
•
•
•
Assign an area that also activates the D9210B
Assign a point to the door
Program the door state to change the time when
the arm state changes
Assign a point to the door
Program the door state to change the time when
the arm state changes
Blank
Only the area assigned to the D#
Entry Area disarms this door.
Entry Area disarms this door.
Allow for the Strike relay to activate upon a fire
alarm
alarm
Enter the keypad number (CC#) which determines
the scope of the user ID’s disarming rights. Areas
disarm on the basis of this keypad’s scope and the
authority level of the user.
the scope of the user ID’s disarming rights. Areas
disarm on the basis of this keypad’s scope and the
authority level of the user.
Programming the Interlock point.
Door #
D# Custom Function
Default:
1
Selection:
1 to 8
Default:
0 (Disabled)
Enter the number of the door you are programming.
Selection:
0, 128-143
0
Custom function disabled.
The D9412GV2 supports up to eight
doors. The D7412GV2 supports two
doors. The D7412GV2 supports two
128-143
The custom function number that
executes upon a valid ID, given the
appropriate user access level and
area arm state.
executes upon a valid ID, given the
appropriate user access level and
area arm state.
doors.
D# Entry Area #
You can program a custom function to run at the
keypad programmed for CC# Scope. This custom
function activates only for users with an L##
Function Level? Assignment (refer to Section
keypad programmed for CC# Scope. This custom
function activates only for users with an L##
Function Level? Assignment (refer to Section
Default:
Blank
Selection:
Blank, 1 to 8
The area assigned to the door
controller to which the reader allows
access.
controller to which the reader allows
access.
1 to 8
User Interface on page 76) in which a valid ID can
execute a custom function during the armed or
disarmed state. The user number to which the token
is assigned must have an assigned pass code.
execute a custom function during the armed or
disarmed state. The user number to which the token
is assigned must have an assigned pass code.
Blank
Door controller does not function.
Assign an area to the door controller. This entry
allows the D9210B to be polled, activating
communication to the control panel. This is also the
area a user exits when initiating an REX.
allows the D9210B to be polled, activating
communication to the control panel. This is also the
area a user exits when initiating an REX.
If D# Disarm On Open is set to Yes for the same
door, and L## Function Level? is set to D or C, the
custom function executes when the door is physically
opened.
door, and L## Function Level? is set to D or C, the
custom function executes when the door is physically
opened.
A user’s access level and the armed state
All SDI devices, regardless of area
of the area determine whether the custom
assigned, report to Area 1, Account 1 by
default upon SDI failure. If a D9210B
becomes disconnected, an SDI Fail ##
and a Missing Point ### Event is
created.
becomes disconnected, an SDI Fail ##
and a Missing Point ### Event is
created.
If the D9210B is not programmed with a
D# Entry Area, 9210 NOT READY
appears at the keypad with this door
assigned to it when you press the
[ENTER] key
D# Entry Area, 9210 NOT READY
appears at the keypad with this door
assigned to it when you press the
[ENTER] key
function activates. This access level is