Bosch Appliances Video Game Controller D9412GV2 User Manual
D9412GV2/D7412GV2 | Program Entry Guide | 3.0 RADXUSR1/RADXUSR2
EN | 84
Bosch Security Systems, Inc. | 10/08 | F01U003636-04
This window does not affect tokens and
3.0 RADXUSR1/RADXUSR2
cards. It only affects the pass code of the
master user.
master user.
•
•
•
•
•
•
•
•
3.1
Pass Code or Token Worksheet
These programming items assign:
When using the Add/Change User
a pass code to user groups 001 to 249,
function at the keypad, the authority levels
and the changes made affect the master
and the changes made affect the master
areas by authority level, and
user’s pass code and the entire group’s
a User Group Window.
token or cards.
Two handlers in the D5200 Programmer are used to
program the users:
program the users:
When using the ACCESS CTL LVL
function at the keypad, the whole group is
function at the keypad, the whole group is
RADXUSR1 Handler programs users 000 to 124.
affected by whether or not the level is on
or off for access control functions only.
or off for access control functions only.
RADXUSR2 programs users 125 to 249
(D9412GV2 only).
(D9412GV2 only).
When using the DELETE USER?
3.1.1 User
Groups
function, the whole group is deleted. You
cannot delete each user within the group
cannot delete each user within the group
For the D9412GV2, there are 249 groups (99 groups
for the D7412GV2) consisting of one user with a pass
code and token (master) and three users with tokens
or cards but not a pass code (sub-user). All users in
the group share the same authority level as the
master user.
for the D7412GV2) consisting of one user with a pass
code and token (master) and three users with tokens
or cards but not a pass code (sub-user). All users in
the group share the same authority level as the
master user.
individually. Use the ADD/CHG USER?
function to change a user token or card
instead of deleting the whole group.
function to change a user token or card
instead of deleting the whole group.
3.1.4 User
Name
Each user group can be assigned one U### Name.
This name is logged and sent to the central station
for all the users in the group. The user ID is used to
differentiate which user’s token or card was
executed.
This name is logged and sent to the central station
for all the users in the group. The user ID is used to
differentiate which user’s token or card was
executed.
3.1.2 Pass
Codes
In a control panel with factory default settings, only
the master user has an assigned pass code. A pass
code can be three to six digits. Entering three digits in
User ### chooses the user. Programming the U001
Passcode assigns a pass code to the master user.
Sub-users cannot use the pass code. Do not assign
tokens or cards to User ID 0 (zero), which is reserved
for the service pass code.
Passcode Tamper
If a user enters six consecutive invalid pass codes at
the same keypad, the control panel sends a User
Code Tamper report to the cental station. The invalid
pass code count resets when a valid passcode is
entered at the same keypad. Refer to R# Usr Code
Tamper in Table 11 on page 18 for information on
enabling this report.
The passcode tamper condition is also reported in a
manually initiated Extended Test Report and to RPS
through control panel diagnostics. As a result, the
tamper condition is reset after the successful
completion of a manual report or when disconnecting
from an RPS session. The tamper condition is not
reset when the control panel reboots.
3.1.3 User
the master user has an assigned pass code. A pass
code can be three to six digits. Entering three digits in
User ### chooses the user. Programming the U001
Passcode assigns a pass code to the master user.
Sub-users cannot use the pass code. Do not assign
tokens or cards to User ID 0 (zero), which is reserved
for the service pass code.
Passcode Tamper
If a user enters six consecutive invalid pass codes at
the same keypad, the control panel sends a User
Code Tamper report to the cental station. The invalid
pass code count resets when a valid passcode is
entered at the same keypad. Refer to R# Usr Code
Tamper in Table 11 on page 18 for information on
enabling this report.
The passcode tamper condition is also reported in a
manually initiated Extended Test Report and to RPS
through control panel diagnostics. As a result, the
tamper condition is reset after the successful
completion of a manual report or when disconnecting
from an RPS session. The tamper condition is not
reset when the control panel reboots.
3.1.3 User
Group
Window
Use U### User Group to enable and disable the
U### Passcode for up to eight different time periods
throughout the day. Assign the number (1 to 8)
programmed in U### User Group to a User
Windows #. If the user is outside a window,
COMMAND DISABLED appears on the keypad after
the user enters the pass code and presses [ENTER].
U### Passcode for up to eight different time periods
throughout the day. Assign the number (1 to 8)
programmed in U### User Group to a User
Windows #. If the user is outside a window,
COMMAND DISABLED appears on the keypad after
the user enters the pass code and presses [ENTER].
When using a D1260 Keypad, User 249
text is used for contact information text
(such as telephone numbers). If a D1260
text is used for contact information text
(such as telephone numbers). If a D1260
is installed on the system, do not use
User 249 for user ID information.
User 249 for user ID information.
3.1.5 Tokens
and
Cards
The master user assigned the pass code can also be
assigned a token or card by programming the U###
Mstr Site and U### Mstr Crd Data.
Three more tokens or cards are assigned to the user
group for sub-users using the U### SU# Site and
U### SU# C/D.
assigned a token or card by programming the U###
Mstr Site and U### Mstr Crd Data.
Three more tokens or cards are assigned to the user
group for sub-users using the U### SU# Site and
U### SU# C/D.