Bosch 3540 User Manual
3.
Safety
“READ ALL INSTRUCTIONS” — Failure to follow the SAFETY RULES identified by BULLET (•) symbol listed
BELOW and other safety precautions, may result in serious personal injury.
BELOW and other safety precautions, may result in serious personal injury.
Tool Use and Care
•
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable. It
allows for work to shift, causes binding of the tool and
loss of control.
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable. It
allows for work to shift, causes binding of the tool and
loss of control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed. Do not use the
tool for purpose not intended.
application. The correct tool will do the job better and
safer at the rate for which it is designed. Do not use the
tool for purpose not intended.
•
Do not use tool if switch does not turn it “oN” or
“off”. Any tool that cannot be controlled with the switch
is dangerous.
“off”. Any tool that cannot be controlled with the switch
is dangerous.
•
Disconnect the plug from the power source before
making any adjustments or changing accessories.
Such preventive safety measures reduce the risk of
starting the tool accidentally.
making any adjustments or changing accessories.
Such preventive safety measures reduce the risk of
starting the tool accidentally.
•
Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges, are less likely
to bind and easier to control. When mounting saw blades
be certain that the arrow on the blade matches the
direction of the arrow marked on the tool and that the
teeth are also pointing in the same direction.
maintained tools, with sharp cutting edges, are less likely
to bind and easier to control. When mounting saw blades
be certain that the arrow on the blade matches the
direction of the arrow marked on the tool and that the
teeth are also pointing in the same direction.
•
inspect guards before using a tool. Keep guards in
place. check moving parts for binding or any other
condition that may affect the normal operation or
safety features of the tool. if damaged, have tool
serviced before using the tool. Many accidents are
caused by poorly maintained tools.
place. check moving parts for binding or any other
condition that may affect the normal operation or
safety features of the tool. if damaged, have tool
serviced before using the tool. Many accidents are
caused by poorly maintained tools.
•
Do not alter or misuse tool. Any alteration or
modification is a misuse and may result in serious
personal injury.
modification is a misuse and may result in serious
personal injury.
•
The use of any other accessories not specified in this
manual may create a hazard. Accessories that may be
suitable for one type of tool, may become hazardous
when used on an inappropriate tool.
manual may create a hazard. Accessories that may be
suitable for one type of tool, may become hazardous
when used on an inappropriate tool.
Service
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in misplacing internal
wires and components which could cause serious
hazard.
repair personnel. Service or maintenance performed by
unqualified personnel may result in misplacing internal
wires and components which could cause serious
hazard.
•
when servicing a tool, use only identical replacement
parts. follow instructions in the maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a hazard.
parts. follow instructions in the maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a hazard.
Safety Rules for
Tile Saws
•
To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch
plug with wet hands.
connections dry and off the ground. Do not touch
plug with wet hands.
•
To reduce the risk of electric shock, plug tile saw into
Ground fault circuit interrupter (Gfci) protected
outlet only. if a Gfci protected outlet is not available,
use a portable receptacle with built-in Gfci
protection.
Ground fault circuit interrupter (Gfci) protected
outlet only. if a Gfci protected outlet is not available,
use a portable receptacle with built-in Gfci
protection.
•
Disconnect saw from power source before making
adjustments, servicing, cleaning, or changing blade.
adjustments, servicing, cleaning, or changing blade.
•
Replace damaged tile blades before operating.
•
Use tool only with smooth edge tile blades free of
openings and grooves.
openings and grooves.
•
after turning saw off, wait for blade to stop before
removing cutoff pieces or changing settings.
removing cutoff pieces or changing settings.
•
Use top guard for every operation for which it can be
used.
used.
•
Do not reach in back of the saw blade with either
hand to hold down or support the workpiece, remove
scraps, or for any other reason. The proximity of the
spinning tile blade to your hand may not be obvious and
you may be seriously injured.
hand to hold down or support the workpiece, remove
scraps, or for any other reason. The proximity of the
spinning tile blade to your hand may not be obvious and
you may be seriously injured.
•
always disconnect the power cord from the power
source before making any adjustments or attaching
any accessories. You may unintentionally start the saw,
leading to serious personal injury.
source before making any adjustments or attaching
any accessories. You may unintentionally start the saw,
leading to serious personal injury.
•
Do not use the saw until the table is clear of all tools,
scraps, etc., except the workpiece and related feed or
supported devices for the operation planned. Small
debris or loose pieces of tile or other objects that contact
the revolving blade can be thrown with high speed at the
operator.
scraps, etc., except the workpiece and related feed or
supported devices for the operation planned. Small
debris or loose pieces of tile or other objects that contact
the revolving blade can be thrown with high speed at the
operator.
•
empty water from tile saw base before transporting.
Water left in base can splash into electrical components.
Water left in base can splash into electrical components.
WARNING
!
“SaVe TheSe iNSTRUcTioNS”
SM_2610008271_12-09:tile saw 12/17/09 3:25 PM Page 3