Alpine CDA-105RI User Manual
21
-EN
Setting Adaptive Steering Remote Control
This unit is compatible with the adaptive steering remote control.
This function allows operation by sending the steering remote control
signal to the unit.
To use the steering remote control, perform the following button
operations after setting to ON and pressing
This function allows operation by sending the steering remote control
signal to the unit.
To use the steering remote control, perform the following button
operations after setting to ON and pressing
/ENT.
For details, consult your nearest Alpine dealer.
1
Select the assigned function by turning the Rotary
encoder.
encoder.
(e.g. Select SOURCE)
POWER
SOURCE
BAND
VOL. UP
VOL. DN
PAUSE
MUTE
BWD
FWD
P. UP
P. DN
A.PROC
POWER
2
Press the steering remote control button until the
changed signal value of steering remote control
appears in the left of the display.
changed signal value of steering remote control
appears in the left of the display.
(e.g. Press SOURCE of the steering remote control button.)
The changed steering remote control signal appears in the
left of the display.
left of the display.
3
Press
/ENT to execute the setting value.
The confirmed signal value of steering remote control
appears in the right of the display. With doing so, the
function of the unit is assigned to the steering remote
control button.
appears in the right of the display. With doing so, the
function of the unit is assigned to the steering remote
control button.
4
Repeat steps 1 to 3, and set each button.
When settings have been completed, press
/ESC to
return to the previous mode.
Turning Mute Mode On/Off (INT MUTE)
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from the
device.
automatically muted whenever the interrupt signal is received from the
device.
• When Bluetooth is set to ADAPTE, INT MUTE cannot be set. Refer to
• When the Bluetooth INTERFACE (KCE-400BT) is connected, set INT
MUTE to OFF.
Setting the AUX+ SETUP Mode
You can input the audio of an external device, (such as a Portable audio
player) to the Bluetooth interface connector of this unit. A special
Conversion cable (KCE-237B) is necessary to adapt the Bluetooth
interface connector as an AUX IN.
A portable music device and a Bluetooth INTERFACE (KCE-400BT)
cannot be connected to the Bluetooth interface connector at the same
time.
player) to the Bluetooth interface connector of this unit. A special
Conversion cable (KCE-237B) is necessary to adapt the Bluetooth
interface connector as an AUX IN.
A portable music device and a Bluetooth INTERFACE (KCE-400BT)
cannot be connected to the Bluetooth interface connector at the same
time.
You can change the AUX+ name display when AUX+ SETUP is set to
ON. Press
ON. Press
/ENT when AUX+ SETUP is set to ON, and select
AUX+ NAME by turning the Rotary encoder, then press
/ENT.
After that, turn the Rotary encoder to select the desired AUX+ name.
Setting the AUX+ Level (AUX IN GAIN)
After setting to ON in “Setting the AUX+ SETUP Mode”, this setting
can be carried out.
can be carried out.
Setting the External Digital Input
When an ALPINE Ai-NET compatible digital audio processor
(PXA-H701) and a DVD player (DVE-5207) not compatible with
Ai-NET are connected, set DIGITAL AUX to ON to enjoy 5.1-channel
surround sound.
You can change the DIGITAL AUX name display when DIGITAL AUX
is set to ON. Press
surround sound.
You can change the DIGITAL AUX name display when DIGITAL AUX
is set to ON. Press
/ENT when DIGITAL AUX is set to ON, and
select DIGITAL AUX name by turning the Rotary encoder, then press
/ENT. After that, turn the Rotary encoder to select the desired
Digital AUX name.
• Press SOURCE/
, and select the DIGITAL-AUX mode, and adjust
the volume, etc.
• After input selection is completed, turn the ignition off and back on
again. Setting of the optical digital input switch is completed.
• Depending on the connected audio processor, DVD player sound
may continue to be output, even though the source is changed to
another one. If this occurs, set the DVD player’s power to OFF.
another one. If this occurs, set the DVD player’s power to OFF.
Setting the AUX Mode (V-Link)
You can input TV/video sound by connecting an optional Ai-NET/RCA
Interface cable (KCA-121B) or Versatile Link Terminal (KCA-410C) to
this component.
You can change the AUX name display when AUX IN is set to ON.
Press
Interface cable (KCA-121B) or Versatile Link Terminal (KCA-410C) to
this component.
You can change the AUX name display when AUX IN is set to ON.
Press
/ENT when AUX IN is set to ON, and select AUX NAME by
turning the Rotary encoder, and then press
/ENT.
After that, turn the Rotary encoder to select the desired AUX name.
If the KCA-410C is connected, it is possible to select two AUX names.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/
to select AUX mode and
then press BAND/TA to select your desired device.
STEERING ON / STEERING OFF (Initial Setting)
MUTE ON / MUTE OFF (Initial setting)
FF SOURCE FF
DE SOURCE FF
The changed signal value of steering remote control
DE SOURCE DE
The confirmed signal value of steering remote control
AUX+ ON / AUX+ OFF (Initial Setting)
AUX+ ON : Set to ON when a portable device is connected. If
SOURCE/
is pressed and AUX+ is selected, the
sound of the portable device is input to the unit.
AUX+ OFF : When set to OFF, AUX+ source cannot be selected.
LOW (Initial setting ) / HIGH
LOW : Decreases the external input audio level.
HIGH : Increases the external input audio level.
D-AUX ON / D-AUX OFF (Initial setting)
AUX IN ON / AUX IN OFF (Initial setting)